The AirTAC Airtac SC32 Standard Cylinder SC32X600SH is a genuine double-acting standard air cylinder with a Ø32mm bore and 600mm stroke, PT1/8 air ports and adjustable end cushioning. It is used for push, pull, lift and clamp motion in industrial automation.
The AirTAC SC32X600SH is a double-acting tie-rod cylinder with a 32 mm bore and a non-standard 600 mm stroke, extending beyond the standard 1000 mm maximum for this bore. It delivers 402 N of push force at 0.5 MPa and up to 724 N at the maximum operating pressure of 0.9 MPa, driven by a 12 mm diameter piston rod with an M10x1.25 rod thread.
This model is equipped with a built-in magnet (-S) for direct mounting of CMSG/DMSG/EMSG sensors and features high-temperature Viton (FKM) seals (-H), shifting the operating temperature range from the standard -20 to +70 °C to 0 to +150 °C. The port thread is standard PT1/8, and the body length A is 140 mm.
| Model | Airtac SC32 Standard Cylinder SC32X600SH |
|---|---|
| Series | SC standard tie-rod cylinder |
| Bore size | Ø32 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 21 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SC series datasheet. Operating pressure 0.15–1.0 MPa, proof pressure 1.5 MPa, temperature −20 to +70 °C. Confirm against the product label before installation. Thread options: PT (standard) / G.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | — |
| Max (approx.) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SC | Standard tie-rod cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related variants: SCD (double rod), SCJ (adjustable stroke), SCT (multi-position). Seals: TPU standard / H = Viton / N = NBR. Thread: blank = PT, G = G thread.
The Viton seals allow the SC32X600SH to reliably operate sterilisation doors and material handling systems inside autoclaves and clean steam environments up to 150°C.
The 600 mm stroke and built-in magnetic piston enable multi-position sensing for sorting small components on conveyors, with CMSG sensors providing precise end-of-stroke and mid-stroke confirmation.
With a push force of 724 N at 0.9 MPa, this cylinder actuates lightweight diverters or gates on heated production lines, where standard seals would degrade rapidly.
For applications requiring more force, stepping up to the 40 mm bore SC40 series provides 628 N of push at 0.5 MPa. The 600 mm stroke on a 12 mm rod requires careful side-load management; consider an external linear guide to prevent rod bending and premature bearing wear.
When replacing this cylinder, ensure a 5-point match: 32 mm bore, 600 mm stroke, PT1/8 port thread, the built-in magnet for sensor compatibility, and Viton seals for high-temperature operation. This tie-rod cylinder is shorter than an ISO 15552 profile and is not dimensionally interchangeable with that standard.
Quick checklist
At the standard 0.5 MPa operating pressure, the push force is 402 N and the pull force is 345 N. At the maximum operating pressure of 0.9 MPa, the push force increases to 724 N. The theoretical maximum force at 1.0 MPa is 82 kgf.
No. The AirTAC SC series is a tie-rod cylinder and is physically shorter than an ISO 15552 profile cylinder of the same bore and stroke. It is not dimensionally interchangeable. It is a direct replacement only for another AirTAC SC32 tie-rod cylinder matching this specific stroke, port, magnet, and seal configuration.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.