Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S
The AirTAC Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 80 to 110 mm on the machine — no shims, no part change.
- BoreØ100 mm
- Max stroke110 mm
- Adjustable range80–110 mm
- Adjuster threadM27×2.0
- Port sizePT3/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S
The AirTAC SDAJ100X110-30S is a double-acting compact cylinder featuring an external adjustable extend stop. An M27x2.0 adjuster screw lets you dial the forward stroke down from 110 mm to 80 mm directly on the machine, eliminating the need for shims or part swaps during changeovers. The short riveted body saves valuable axial mounting depth where a larger profile cylinder will not fit.
Because the adjuster sets the mechanical stop rather than the piston area, output force equals a standard SDA of this bore, delivering about 3927 N push at 0.5 MPa. This specific configuration includes a built-in piston magnet (-S) for AirTAC reed or electronic switches. End shock is managed by a fixed NBR bumper, which decelerates the stroke end but is not an adjustable air cushion.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S Technical Specifications
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 110 mm |
| Adjustable range | 80 – 110 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. Force is unchanged from a standard SDA of the same bore. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Force matches a standard SDA of the same bore; the adjuster only sets the stop position, not the area. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S Is Used
Heavy Press Tuning
Dial the M27x2.0 stop down to 80 mm during trial forming runs to prevent over-travel on thick steel blanks before locking the final 110 mm position.
Pallet Lift Stops
Lift loads up to 200.2 kg vertically and fine-tune the extend end to clear varying pallet heights without changing the actuator body.
Large Clamp Changeover
Adjust the forward stop on-site for different fixture widths, using the 3927 N push force at 0.5 MPa to secure heavy cast molds.
Is the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S the Right Cylinder?
When sizing this 100 mm bore actuator, evaluate your force requirements bidirectionally. Stepping down to an SDAJ80 yields 2513.3 N push at 0.5 MPa, whereas this SDAJ100 provides 3927 N. For load handling, a safe working load is roughly 2356 N (about 60 percent of the 0.5 MPa figure), translating to a vertical lift capacity of about 200.2 kg with a 2:1 safety margin.
This model is ideal for heavy setups requiring frequent on-site stroke tuning between 80 and 110 mm. It features a PT3/8 port, a 32 mm rod, and female M18x1.5 rod-end threads. Remember that a plain cylinder does not hold its load on air loss or valve centering; the fixed bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 80–110 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M27×2.0 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S FAQ
At 0.5 MPa it provides 3927 N push and 3524.9 N pull. At 0.7 MPa it provides 5497.8 N push and 4934.8 N pull. The theoretical maximum push is 801 kgf at 1.0 MPa.
The R (M27x2.0) screw shortens the extend stop by up to 30 mm, giving a usable range of 80 to 110 mm. The included -S magnet works with AirTAC reed or electronic switches for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X110-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.