Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S
The AirTAC Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S is a genuine double-acting COMPACT cylinder (Ø100mm bore) whose extend end-position is set by an external M27×2.0 adjustment screw. You can dial the stroke anywhere from 30 to 60 mm on the machine — no shims, no part change.
- BoreØ100 mm
- Max stroke60 mm
- Adjustable range30–60 mm
- Adjuster threadM27×2.0
- Port sizePT3/8
- CushionFixed NBR bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S
The AirTAC SDAJ100X60-30S is a compact double-acting single-rod cylinder featuring an external adjustable extend stop. Turning the R (M27x2.0) screw lets you dial the extend end-position anywhere between 30 and 60 mm directly on the machine, eliminating the need for shims or part swaps during changeover. Retract travel remains full length.
Because the adjuster sets the mechanical stop rather than the piston area, output force equals a standard SDA of this bore, yielding 3927 N push at 0.5 MPa. The short riveted body saves axial mounting depth where larger profile cylinders will not fit, and the built-in magnet (-S) supports AirTAC reed or electronic switches for end-position confirmation. End shock is managed by a fixed NBR bumper, not an adjustable air cushion.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S Technical Specifications
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø100 mm |
| Max stroke | 60 mm |
| Adjustable range | 30 – 60 mm |
| Adjuster thread (R) | M27×2.0 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M18×1.5 F / M26×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. Force is unchanged from a standard SDA of the same bore. Specifications follow the official AirTAC SDAJ datasheet.
Theoretical Output Force (Ø100mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 3927 N | 3525 N |
| 0.7 MPa | 5498 N | — |
| Max (@1.0 MPa) | 801 kgf | |
Force matches a standard SDA of the same bore; the adjuster only sets the stop position, not the area. Actual usable force is lower than theoretical due to friction.
Model Code: Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 100 | Bore size in mm. |
| ×60 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Where the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S Is Used
Press Tooling Changeover
Dial the extend stop from 30 to 60 mm via the M27x2.0 screw to accommodate different material thicknesses on the fly without swapping mechanical spacers.
Heavy Vertical Lifting
Leverage the 3927 N push at 0.5 MPa to raise 200.2 kg loads with a 2:1 margin, using the fixed NBR bumper to soften the final end-of-stroke impact.
Assembly Line Positioning
Use the built-in magnet with reed or electronic switches to confirm reach during trial positioning, fine-tuning the extend endpoint exactly where the 100 mm bore power is needed.
Is the Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S the Right Cylinder?
When sizing this 100 mm bore actuator, evaluate your force requirements both ways. Stepping down, the SDAJ80 provides 2513.3 N push at 0.5 MPa, making this SDAJ100X60-30S the correct choice when you need the full 3927 N to overcome higher friction or move heavier masses. The 100 mm bore also yields a safe working load of roughly 2356 N (about 60% of the 0.5 MPa figure) and can vertically lift approximately 200.2 kg with a 2:1 safety margin.
This model is specified for setup-heavy lines requiring frequent on-site stroke tuning between 30 and 60 mm. It features a PT3/8 port, a female M18x1.5 rod-end thread, and the -S magnet for switch sensing. Remember that a plain cylinder does not hold its load on air loss or when the valve is centred; the piston drifts and the fixed bumper only decelerates near the stroke end. For secure load holding without live pressure, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Need on-machine stroke fine-tuning?
- ✓ Target position within 30–60 mm
- ✓ Force at your working pressure
- ✓ Access to reach the R adjuster
- ✓ Magnet (S) for sensors?
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Lock the M27×2.0 adjuster after setting the stroke.
- check Avoid side load on the piston rod.
- check Front/rear covers are riveted — do not dismantle.
- check Installation by qualified personnel per AirTAC docs.
Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S FAQ
This 100 mm bore double-acting cylinder delivers 3927 N push and 3524.9 N pull at 0.5 MPa, 5497.8 N push and 4934.8 N pull at 0.7 MPa, with a theoretical maximum of 801 kgf at 1.0 MPa.
The external R (M27x2.0) screw shortens the extend stroke by up to 30 mm, allowing usable travel between 30 and 60 mm without altering the 3927 N force. The included -S magnet works with AirTAC reed or electronic switches for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SDAJ Cylinders
Request a Quote for Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ100X60-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.