Airtac SE80 Standard Cylinder SE80AX270S
The AirTAC Airtac SE80 Standard Cylinder SE80AX270S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 270mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke270 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80AX270S
The AirTAC SE80AX270S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It generates 2513 N of push force at 0.5 MPa and features a 270 mm stroke. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while maintaining a standardized ISO 15552 interface.
This specific configuration includes a SUS420J2 stainless steel rod (code A) for corrosive or washdown environments, and a built-in magnet (code S) for position sensing. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, softening hard stops at high cycle rates without relying on fixed rubber bumpers.
Airtac SE80 Standard Cylinder SE80AX270S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80AX270S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 270 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80AX270S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×270 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80AX270S Is Used
Pallet Stretch Wrapper Clamp
Secures the film roll carriage on an orbital pallet wrapper, using the 2513 N thrust to maintain tension against the load while the SUS420J2 rod resists humidity in damp warehouse environments.
Bottling Line Diverter Gate
Actuates a high-speed lane diverter on a 12000 BPH glass bottle filling line, relying on the 270 mm stroke to fully open the guide rails and the adjustable cushion to soften rapid end stops.
Injection Mold Platen Ejector
Drives a secondary ejector pin plate on a 200-ton injection molding machine, where the stainless rod withstands occasional water spray from mold cooling lines and the DMSE sensor confirms retraction.
Is the Airtac SE80 Standard Cylinder SE80AX270S the Right Cylinder?
Selecting this 80 mm bore provides 2513 N push at 0.5 MPa. If your assembly requires less force, the 63 mm bore offers 1559 N; if you need more thrust, the 100 mm bore provides 3927 N. Because the 270 mm stroke creates a long unsupported rod extension, an external guide is recommended to prevent rod-bearing bending under side loads. As a standard ISO 15552 cylinder, it serves as a drop-in replacement sharing standardized mounting hardware and a PT3/8 port.
Note that a plain SE cylinder drifts when air is exhausted or a valve centers; it cannot hold a load without live pressure. For position holding, consider a BSE rod lock. This model's -S magnet integrates directly with AirTAC CMSE reed and DMSE electronic sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80AX270S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force is 3518 N. The maximum push force is 513 kgf at 1.0 MPa.
Yes, the SE80AX270S is dimensionally interchangeable with other ISO 15552 profile cylinders, matching the 80 mm bore footprint, PT3/8 port, and standard mounting accessories for direct retrofitting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80AX270S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.