Airtac SE80 Standard Cylinder SE80AX600S
The AirTAC Airtac SE80 Standard Cylinder SE80AX600S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 600mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke600 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80AX600S
The AirTAC SE80AX600S is a double-acting single-rod ISO 15552 profile cylinder engineered for rigorous linear motion. It delivers a robust 2513 N push force at 0.5 MPa alongside a 2268 N pull, utilizing an 80 mm bore and a 600 mm stroke. The SUS420J2 stainless steel rod (code A) provides essential corrosion resistance for washdown or chemically aggressive settings.
Built to the VDMA 24562 standard, this extruded aluminum body omits external tie rods for a flush, compact footprint that simplifies bracket mounting. The integrated magnet (-S) directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-travel detection, while the field-adjustable air cushioning at both ends allows you to tune deceleration and protect the endcaps during high-speed 30-800 mm/s cycling.
Airtac SE80 Standard Cylinder SE80AX600S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80AX600S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80AX600S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80AX600S Is Used
Palletizer Film Roll Feed
Drives the heavy horizontal carriage of a palletizing film roll dispenser, relying on the 2513 N push at 0.5 MPa and SUS420J2 rod to withstand occasional washdowns in packaging facilities.
Press Brake Demolding
Pushes heavy stamping dies out of a hydraulic press brake, utilizing the 600 mm stroke and field-adjustable air cushions to soften the impact during rapid 30-800 mm/s extraction.
Beverage Line CIP Pusher
Actuates diverter gates in a clean-in-place beverage line, where the corrosion-resistant stainless steel rod endures frequent chemical spray and the S magnet tracks position via DMSE sensors.
Is the Airtac SE80 Standard Cylinder SE80AX600S the Right Cylinder?
When sizing this 80 mm bore, stepping down to a 63 mm cylinder reduces the 0.5 MPa push to 1559 N, whereas stepping up to a 100 mm bore increases it to 3927 N. Because this is a standard 600 mm stroke, the 25 mm rod and M20x1.5 thread handle substantial loads, but an external guide is strongly recommended to prevent rod-bearing bending under long unsupported side loads. As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement sharing standard mounting hardware, PT3/8 ports, and a 36 mm cushion length. Note that the adjustable cushion only decelerates the piston near stroke end; it does not lock the load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80AX600S FAQ
The SE80AX600S generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum of 513 kgf at 1.0 MPa. It uses a PT3/8 port, a 25 mm rod with an M20x1.5 thread, and operates at speeds of 30-800 mm/s.
No, the adjustable air cushion only decelerates the piston near the end of stroke; it does not lock or hold a load if air is exhausted. For position holding, an external rod lock or pilot-operated check valve is required. Dimensionally, it is an ISO 15552 profile cylinder, making it a drop-in replacement for other ISO 15552 cylinders using standard mounting accessories.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80AX600S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.