Airtac SE80 Standard Cylinder SE80BX10SH
The AirTAC Airtac SE80 Standard Cylinder SE80BX10SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 10mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke10 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80BX10SH
The AirTAC SE80BX10SH is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa. It features a SUS304 stainless steel rod and FKM Viton seals, expanding the operating temperature range up to 150 C for harsh washdown environments. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Because this configuration includes a built-in magnet, it is fully primed for AirTAC CMSE reed and DMSE electronic position sensing. The end caps house field-adjustable air cushioning at both ends, allowing technicians to dial in the exact deceleration needed to soften hard mechanical stops during rapid cycling.
Airtac SE80 Standard Cylinder SE80BX10SH Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80BX10SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 10 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80BX10SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80BX10SH Is Used
Palletizer Clamp Arm
Drives the clamping jaw on a palletizer, utilizing the 2513 N push force to secure heavy boxes while the SUS304 rod withstands dusty warehouse environments.
Food Washdown Gate
Actuates a diverting gate in a food processing line, where the FKM Viton seal survives 150 C cleaning cycles and the lack of external tie rods prevents debris buildup.
Injection Mold Ejector
Pushes an ejector pin plate on a small injection molding machine, relying on the 36 mm adjustable cushion to gently brake the 25 mm rod at high speeds.
Is the Airtac SE80 Standard Cylinder SE80BX10SH the Right Cylinder?
Selecting this 80 mm bore makes sense when an application requires substantial thrust, as it provides 2513 N of push at 0.5 MPa. If you need to step down, the 63 mm bore offers 1559 N of push; stepping up to the 100 mm bore provides 3927 N. This specific model carries a PT3/8 port and M20x1.5 rod thread, meaning it handles high side loads well, though external guides are always recommended for any unsupported load. As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standard mounting accessories like FA or LB brackets.
Note that a standard SE cylinder cannot hold a load in place if air pressure is lost or the valve is centered, as the piston will drift. If your application requires static holding, you must integrate an external pilot-operated check valve or pivot to the AirTAC BSE rod-lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80BX10SH FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N. The maximum push force is 513 kgf at 1.0 MPa. It operates at speeds between 30-800 mm/s.
Yes. The SE80BX10SH is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint and accessory interface of other ISO 15552 profile cylinders. Just ensure your porting matches the PT3/8 threads.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80BX10SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.