Airtac SE80 Standard Cylinder SE80BX60SH
The AirTAC Airtac SE80 Standard Cylinder SE80BX60SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 60mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke60 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80BX60SH
The AirTAC SE80BX60SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for rigorous washdown and high-temperature environments. Equipped with an 80 mm bore and a 60 mm stroke, it yields 2513 N of push force at 0.5 MPa and up to 3518 N at 0.7 MPa. The B-series configuration specifies a SUS304 stainless steel piston rod, while the H-code seal upgrades the standard elastomer to FKM (Viton), extending the operating temperature range from -20 to +150 degrees C.
Unlike traditional tie-rod bodies, this actuator utilizes a square extruded aluminum barrel that omits external tie rods, yielding a compact, flush-mounting profile that resists trapped debris. It includes a built-in magnet (-S) for direct compatibility with AirTAC CMSE reed and DMSE electronic position sensors. Furthermore, the end caps integrate field-adjustable air cushioning at both ends, allowing technicians to tune the deceleration screws to soften hard end stops during high-speed cycling.
Airtac SE80 Standard Cylinder SE80BX60SH Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80BX60SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 60 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80BX60SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80BX60SH Is Used
Pharmaceutical Mixers
Drives pivot arms on stainless mixing vessels, utilizing the SUS304 rod and FKM seal to withstand caustic chemical washdowns at 150 degrees C.
Food Tray Denesters
Pulls vacuum suction cups to strip trays from magazines, using the 2268 N pull force at 0.5 MPa to overcome stack friction reliably.
Injection Mold Ejectors
Actuates secondary ejector pins inside hot mold environments, leveraging the FKM Viton seals to resist thermal degradation near 150 degrees C.
Is the Airtac SE80 Standard Cylinder SE80BX60SH the Right Cylinder?
When sizing this 80 mm bore actuator, evaluate your force requirements against its 2513 N push at 0.5 MPa. If your application demands less force, stepping down to the 63 mm bore yields 1559 N of push at 0.5 MPa, offering a lighter footprint. Conversely, if you need greater thrust, the 100 mm bore provides 3927 N of push at 0.5 MPa. Because this is a standard double-acting cylinder, it will not hold a load if air pressure is lost or the valve is centered; the piston will drift. For position-holding safety, consider the AirTAC BSE rod-lock variant or an external pilot-operated check valve. As a dimensionally interchangeable ISO 15552 profile cylinder, it serves as a drop-in replacement for other ISO 15552 actuators, matching the 80 mm bore, 60 mm stroke, PT3/8 port, and standard mounting footprint exactly.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80BX60SH FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N. The maximum push force is 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552, serving as a drop-in replacement for other ISO 15552 cylinders. However, as a standard double-acting cylinder, it does not hold a load if air is lost; the piston will drift. You must use an AirTAC BSE rod-lock cylinder or an external lock for fail-safe load holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80BX60SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.