Airtac SE80 Standard Cylinder SE80X1000S
The AirTAC Airtac SE80 Standard Cylinder SE80X1000S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 1000mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke1000 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X1000S
The AirTAC SE80X1000S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding linear motion tasks. It features an 80 mm bore and a 1000 mm stroke, yielding 2513 N of push force at 0.5 MPa and 3518 N at 0.7 MPa. The extruded aluminum barrel lacks external tie rods, presenting a clean, corrosion-resistant profile that mounts flush against machine frames while retaining high structural rigidity.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensing for precise end-of-stroke verification. Field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-stop deceleration via a screw, softening impacts during high-velocity 1000 mm traverses. It operates reliably at speeds between 30-800 mm/s under pressures from 0.15-1.0 MPa.
Airtac SE80 Standard Cylinder SE80X1000S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X1000S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X1000S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X1000S Is Used
Pallet Transfer Line Diversion
Leveraging the 1000 mm stroke and 2513 N push force, this cylinder reliably actuates long-throw diverter arms on high-speed pallet conveyor lines.
Large Carton Erector Flap Folding
The 80 mm bore provides the robust 3518 N extension force at 0.7 MPa needed to fold heavy corrugated cardboard flaps on industrial case erectors.
Automotive Welding Curtain Indexing
Utilizing the built-in magnet for DMSE sensor feedback, it drives the 1000 mm indexing movement of safety curtains in robotic welding cells.
Is the Airtac SE80 Standard Cylinder SE80X1000S the Right Cylinder?
When sizing this 80 mm bore actuator, consider stepping down to the 63 mm variant if your load requires only 1559 N of push at 0.5 MPa, or moving up to the 100 mm bore for 3927 N of push. Because this is a standard 1000 mm stroke, it falls within the maximum standard stroke limit for this bore, but long unsupported strokes inherently introduce rod-bearing bending moments; an external guide is strongly recommended to prevent excessive side-load wear. For drop-in ISO 15552 retrofits, verify the 1000 mm stroke, PT3/8 port, and required mounting accessory. Remember that a standard SE cylinder does not hold a load if air pressure is lost; if your application requires true position holding, explore the BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X1000S FAQ
The SE80X1000S has an 80 mm bore and uses a PT3/8 port. It generates 2513 N of push force and 2268 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 3518 N. The maximum push force is 513 kgf at 1.0 MPa.
Yes, the SE80X1000S is dimensionally interchangeable per ISO 15552 standards. You can use it as a drop-in replacement for other ISO 15552 profile cylinders, utilizing standard mounting hardware and the existing PT3/8 pneumatic connections.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X1000S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.