Airtac SE80 Standard Cylinder SE80X1000SN
The AirTAC Airtac SE80 Standard Cylinder SE80X1000SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 1000mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke1000 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X1000SN
The AirTAC SE80X1000SN is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It delivers a substantial 2513 N push force at 0.5 MPa and a maximum push capacity of 513 kgf at 1.0 MPa, driven by an 80 mm bore and a PT3/8 port. Equipped with an NBR seal, it operates reliably across a 30-800 mm/s speed range while handling a 1000 mm stroke. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Because this unit carries the S option, it includes a built-in magnet for direct mounting of CMSE reed and DMSE electronic sensors along the three integrated side grooves. The field-adjustable air cushioning at both ends features a 36 mm cushion length and can be tuned via a set screw to soften hard end stops at high velocities. Note that while the cushion decelerates the piston near stroke end, it does not lock the load; a BSE rod lock variant is required for position holding without live air pressure.
Airtac SE80 Standard Cylinder SE80X1000SN Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X1000SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X1000SN
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X1000SN Is Used
Pallet Conveyor Diverters
Leveraging the 2513 N push force at 0.5 MPa and 1000 mm stroke, this cylinder actuates heavy pallet diverter arms on high-throughput packaging lines.
Press Brake Ejection
The 36 mm adjustable air cushion softens the 1000 mm stroke end-of-travel, protecting the tooling when ejecting heavy formed metal sheets from a press brake.
Automated Storage Retrieval
The NBR seals and integrated CMSE/DMSE sensor magnet make it ideal for driving robust extraction forks in automated storage and retrieval system (AS/RS) cranes.
Is the Airtac SE80 Standard Cylinder SE80X1000SN the Right Cylinder?
When sizing this 80 mm bore actuator, evaluate your force margins: stepping down to a 63 mm cylinder reduces the 0.5 MPa push to 1559 N, while stepping up to a 100 mm bore increases it to 3927 N. For this 1000 mm stroke, the 25 mm rod and M20x1.5 thread carry significant side loads, but the extended unsupported length makes rod-bearing bending a real risk—an external guide is strongly recommended to prevent premature wear. As a dimensionally interchangeable ISO 15552 component, it serves as a drop-in replacement for other ISO 15552 profile cylinders, matching the PT3/8 port, 80 mm bore, and 1000 mm stroke exactly.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X1000SN FAQ
This 80 mm bore cylinder delivers a push force of 2513 N and a pull force of 2268 N at 0.5 MPa. At 0.7 MPa, the push force is 3518 N, with a maximum push of 513 kgf at 1.0 MPa. It operates at a speed of 30-800 mm/s.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke end; it is not a locking mechanism. If air is exhausted or the valve is centered, the piston will drift. For fail-safe load holding, use a BSE rod lock cylinder or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X1000SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.