Airtac SE80 Standard Cylinder SE80X100H
The AirTAC Airtac SE80 Standard Cylinder SE80X100H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 100mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke100 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X100H
The AirTAC SE80X100H is a double-acting single-rod ISO 15552 profile cylinder engineered for high-temperature service. Equipped with an FKM Viton seal, it expands the standard operating envelope from -20 to +150 degrees Celsius, making it suitable for heated machinery and harsh washdown environments. At 80mm bore, it generates 2513N of push force and 2268N of pull force at 0.5 MPa.
Built to strict VDMA 24562 dimensions, this actuator features a square extruded aluminum barrel without external tie rods, yielding a compact, corrosion-resistant body that mounts flush on automated frames. The field-adjustable air cushion at both ends allows technicians to dial in end-of-stroke deceleration via a set screw, softening hard impacts during high-speed 30-800 mm/s cycling. This specific SKU lacks a built-in position magnet, so it is ready for mechanical actuation but will not trigger AirTAC CMSE or DMSE sensors.
Airtac SE80 Standard Cylinder SE80X100H Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X100H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X100H
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X100H Is Used
Plastic Injection Mold Extraction
Withstands 150C ambient heat near mold platens using its FKM seal, providing 2513N of push to safely extract heavy automotive interior panels from tooling.
Hot-Fill Packaging Sealing
Delivers 2268N of retraction force to pull sealing jaws away from heated film shrink tunnels, utilizing the adjustable cushion to prevent jaw bounce at 800 mm/s.
Metal Stamping Ejection
Uses its 36mm cushion stroke to gently decelerate the 25mm rod when ejecting aluminum stampings from heated dies, avoiding workpiece marking.
Is the Airtac SE80 Standard Cylinder SE80X100H the Right Cylinder?
When sizing this 80mm bore, compare its 2513N push at 0.5 MPa against the smaller 63mm bore, which yields 1559N, or the larger 100mm bore, which provides 3927N. Stepping up to the 100mm cylinder is advised if your load approaches the 513 kgf maximum structural limit, while dropping to the 63mm saves space and air consumption for lighter 1559N tasks. Because this is a double-acting cylinder, it cannot hold a load if air pressure is lost or the valve centers; if your application requires static holding, you must integrate an external BSE rod lock or pilot-operated check valve. The 100mm stroke keeps the rod well-supported, but for any future builds exceeding 300mm, the 25mm piston rod and M20x1.5 thread will experience greater bending moments, requiring an external guide to prevent side-load bearing wear.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X100H FAQ
The 80mm bore generates 2513N of push force and 2268N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 3518N, with a maximum push capacity of 513 kgf at 1.0 MPa. It uses a PT3/8 port and a 25mm rod with an M20x1.5 thread.
No. The SE80X100H is a standard double-acting cylinder, meaning the piston will drift if air is lost or the control valve is centered. The adjustable air cushion only decelerates the piston near stroke end; it does not act as a brake or lock. For static holding, consider an AirTAC BSE series rod lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X100H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.