Airtac SE80 Standard Cylinder SE80X100SN
The AirTAC Airtac SE80 Standard Cylinder SE80X100SN is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 100mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke100 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X100SN
The AirTAC SE80X100SN is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatic actuation. It provides a substantial 2513 N push force at 0.5 MPa, utilizing an 80 mm bore and a 100 mm stroke. The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant exterior that mounts flush against machine frames while simplifying sensor placement along its three integrated grooves.
This specific configuration includes a built-in magnet (S) for non-contact position detection via AirTAC CMSE reed or DMSE electronic switches, alongside NBR seals for standard temperature environments. The cylinder relies on field-adjustable pneumatic cushioning at both ends, allowing technicians to dial in the end-of-stroke deceleration via a set screw to eliminate hard mechanical impacts during high-speed cycling.
Airtac SE80 Standard Cylinder SE80X100SN Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X100SN |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X100SN
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X100SN Is Used
Press Brake Tooling
Provides the 2513 N push force required to actuate lower press brake dies and hold heavy sheet metal bending setups firmly in position.
Pallet Divert Arm
Drives a robust diverting arm on high-throughput packaging conveyor lines, using its 100 mm stroke to push loaded pallets onto secondary routing tracks.
Carton Sealing Press
Applies downward clamping pressure on automated carton sealing machinery, relying on the NBR seals and adjustable cushioning to absorb the 2513 N end-impact.
Is the Airtac SE80 Standard Cylinder SE80X100SN the Right Cylinder?
Delivering 2513 N of push force at 0.5 MPa, this 80 mm bore cylinder is sized for substantial actuation loads. If your application requires less force, stepping down to the 63 mm bore model yields 1559 N of push, whereas stepping up to the 100 mm bore provides 3927 N for heavier moving masses. Because it is a double-acting cylinder, it does not hold a load if air pressure is lost or the valve is centered; the piston will drift, requiring an external rod lock or pilot-operated check valve for fail-safe position holding. To match existing ISO 15552 hardware, specify the 100 mm stroke, PT3/8 port, and the desired mounting accessory.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X100SN FAQ
At 0.5 MPa, the SE80X100SN provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N. The maximum push force is 513 kgf when operated at the maximum rated pressure of 1.0 MPa.
Yes, the SE80X100SN is dimensionally interchangeable per ISO 15552 standards. Its standardized mounting interface and PT3/8 porting allow it to serve as a drop-in replacement for other ISO 15552 profile cylinders, sharing the same mounting hardware and sensor rail dimensions.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X100SN
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.