Airtac SE80 Standard Cylinder SE80X1300S
The AirTAC Airtac SE80 Standard Cylinder SE80X1300S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 1300mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke1300 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X1300S
The AirTAC SE80X1300S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It leverages a 25 mm hard-chrome plated rod and a PT3/8 port to generate 2513 N of push force and 2268 N of pull force at 0.5 MPa, peaking at a maximum 513 kgf push at 1.0 MPa. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Because this configuration includes the -S option, a built-in magnetic piston ring enables contactless position detection using AirTAC CMSE reed or DMSE electronic sensors dropped directly into the three-side sensor groove. To absorb the kinetic energy of a 1300 mm extension, field-adjustable air cushioning at both ends allows technicians to tune the end-of-stroke deceleration precisely via a set screw, preventing hard mechanical impacts.
Airtac SE80 Standard Cylinder SE80X1300S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X1300S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 1300 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X1300S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×1300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X1300S Is Used
Pallet Transfer Rejector
Uses the 1300 mm stroke to push heavy pallets off a high-speed packaging line, relying on 2513 N of push force at 0.5 MPa to overcome sliding friction.
Automated Press Ejection
Reaches deep into a hydraulic press bed to extract formed metal panels, utilizing the 25 mm rod to handle the load and the adjustable cushion to soften the retraction stop.
Multi-Tier Carton Pusher
Actuates across a 1300 mm gap in a sortation hub, using the built-in magnet with DMSE sensors to confirm full extension before indexing the conveyor.
Is the Airtac SE80 Standard Cylinder SE80X1300S the Right Cylinder?
Selecting the SE80X1300S is optimal when an application requires substantial reach paired with high thrust. If 2513 N of push at 0.5 MPa is excessive, stepping down to the 63 mm bore yields 1559 N, whereas moving up to the 100 mm bore provides 3927 N. As a true ISO 15552 profile cylinder, this unit is dimensionally interchangeable with other ISO 15552 cylinders, allowing drop-in retrofits using standardized mounting accessories without altering the existing footprint.
At 1300 mm of stroke, the unsupported mass of the piston and rod introduces significant rod-bearing bending moments under any side load; an external guide rail is strongly recommended to prevent premature seal wear. Furthermore, the adjustable air cushion only decelerates the piston near the stroke ends and does not function as a brake. If the machinery must hold a vertical load without live air pressure, integrate an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X1300S FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N, with an absolute maximum push of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X1300S shares the exact ISO 15552 / VDMA 24562 mounting interface and dimensions, making it a drop-in replacement for other ISO 15552 profile cylinders. It uses a PT3/8 port and M20x1.5 rod thread, so only standard mounting hardware is required.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X1300S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.