Airtac SE80 Standard Cylinder SE80X150S
The AirTAC Airtac SE80 Standard Cylinder SE80X150S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 150mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke150 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X150S
The AirTAC SE80X150S is a double-acting single-rod ISO 15552 profile cylinder delivering 2513 N of push force at 0.5 MPa. Its extruded aluminum barrel eliminates external tie rods, yielding a flush, corrosion-resistant body that mounts cleanly in tight machine spaces. The integrated -S magnet enables precise end-of-stroke detection using AirTAC CMSE reed or DMSE electronic sensors.
Field-adjustable air cushions at both ends allow you to tune end-stop deceleration for heavy 80mm bore loads moving at speeds up to 800 mm/s. Because it follows the ISO 15552 / VDMA 24562 mounting interface, it serves as a drop-in dimensional replacement for comparable standard profile cylinders.
Airtac SE80 Standard Cylinder SE80X150S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X150S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X150S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X150S Is Used
Palletizer Case Pusher
Uses the 2513 N extend force at 0.5 MPa to positively push heavy corrugated cases onto palletizing lanes without bounce-back.
Bottling Line Diverter
Leverages the 150mm stroke and DMSE electronic sensor feedback to accurately route glass containers between filling stations.
Press Tool Ejector
Employs the 36mm adjustable cushion to safely decelerate the 80mm piston when ejecting metal stampings at high cycle rates.
Is the Airtac SE80 Standard Cylinder SE80X150S the Right Cylinder?
Stepping down to the 63mm bore drops the 0.5 MPa push force to 1559 N, while moving up to the 100mm bore raises it to 3927 N, letting you size precisely for the load. Remember that a plain SE cylinder will drift if air is lost or a valve is centered; use a BSE rod lock variant if the application must hold a load without live pressure. For ISO 15552 retrofits, match the 150mm stroke, PT3/8 port, and mounting accessory to ensure a seamless swap.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X150S FAQ
The SE80X150S generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push force of 513 kgf at 1.0 MPa.
Yes, the SE80X150S is dimensionally interchangeable with standard ISO 15552 profile cylinders, sharing the same mounting footprint and PT3/8 port for easy retrofitting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X150S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.