Airtac SE80 Standard Cylinder SE80X15S
The AirTAC Airtac SE80 Standard Cylinder SE80X15S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 15mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke15 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X15S
The AirTAC SE80X15S is a double-acting single-rod ISO 15552 profile cylinder engineered for high-force pneumatic tasks. It delivers 2513 N of push force at 0.5 MPa and reaches 3518 N at 0.7 MPa, making it well-suited for heavy-duty short-stroke actuation. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection across its 15 mm travel. Field-adjustable air cushions at both ends allow mechanics to tune end-stop deceleration, softening impacts even at high cycling speeds up to 800 mm/s.
Airtac SE80 Standard Cylinder SE80X15S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X15S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 15 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X15S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X15S Is Used
Press Fit Bushings
Generates 2513 N of push at 0.5 MPa to seat bearings and bushings into housings within a tight 15 mm stroke, using the adjustable cushion to soften the final impact.
Stamping Markers
Provides rapid part marking and light stamping on metal components, where the 80 mm bore output and integrated DMSE sensor ensure precise, repeatable strikes.
Clamping Fixtures
Secures heavy workpieces during machining operations, applying up to 513 kgf at 1.0 MPa while the flush profile barrel allows tight installation alongside tooling.
Is the Airtac SE80 Standard Cylinder SE80X15S the Right Cylinder?
If 2513 N of push at 0.5 MPa is excessive for your setup, the 63 mm bore offers 1559 N; conversely, stepping up to the 100 mm bore yields 3927 N for heavier loads. Because the 15 mm stroke is very short, side-load stress on the rod bearing is minimal, though any application requiring position retention without live air pressure will need a BSE rod lock, as standard cushions only decelerate the piston and do not hold loads. As a dimensionally interchangeable ISO 15552 cylinder, it drops directly into existing foot, flange, or trunnion hardware utilizing a PT3/8 port and M20x1.5 rod thread.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X15S FAQ
The SE80X15S delivers 2513 N of push force and 2268 N of pull force at 0.5 MPa. At 0.7 MPa, the push force reaches 3518 N, and the maximum push force is 513 kgf at 1.0 MPa.
Yes, the SE80X15S is dimensionally interchangeable per ISO 15552 standards, meaning it serves as a drop-in replacement for other ISO 15552 profile cylinders using the same 80 mm bore, PT3/8 port, and mounting interface.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X15S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.