Airtac SE80 Standard Cylinder SE80X160S
The AirTAC Airtac SE80 Standard Cylinder SE80X160S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 160mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke160 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X160S
The AirTAC SE80X160S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa. It utilizes a square extruded aluminum barrel that eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. This design simplifies integration while maintaining the standardized footprint required for global procurement.
Equipped with a built-in magnet, this unit seamlessly interfaces with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection. The field-adjustable pneumatic cushioning at both ends allows technicians to tune the end-of-stroke deceleration via a set screw, softening hard impacts when moving heavy 513 kgf loads at operating speeds up to 800 mm/s.
Airtac SE80 Standard Cylinder SE80X160S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X160S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 160 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X160S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X160S Is Used
Press Brake Tooling
Provides the 2513 N extend force needed to actuate heavy lower press brake clamps and tooling holders during sheet metal bending setups.
Pallet Dispenser
Cycles empty wooden pallets into high-speed packaging lines, utilizing the 160 mm stroke to push stacks securely into the lifting bay.
Heavy Belt Diverter
Drives a robust routing gate on aggregate processing conveyors, where the 25 mm rod withstands abrasive side loads during product redirection.
Is the Airtac SE80 Standard Cylinder SE80X160S the Right Cylinder?
When sizing this 80 mm bore actuator, evaluate your thrust margins: stepping down to the 63 mm bore drops the 0.5 MPa push output to 1559 N, while stepping up to the 100 mm bore increases it to 3927 N. Because this is a double-acting cylinder, it relies on continuous air pressure to move and will drift if supply is lost or a valve centers—the pneumatic cushion only decelerates the piston near stroke end and does not function as a holding brake. If your assembly requires positive load holding without live pressure, consider the BSE rod-lock variant or an external pilot check valve.
For ISO 15552 dimensional interchangeability, match the 80 mm bore, 160 mm stroke, PT3/8 port, and your specific mounting accessory. The 25 mm piston rod and M20x1.5 end thread provide excellent structural rigidity, though any stroke exceeding 300 mm on this series should incorporate an external guide to prevent rod-bearing bending under high side loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X160S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force increases to 3518 N. The maximum push capacity is 513 kgf when operated at the 1.0 MPa pressure limit.
Yes, the SE80X160S is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint and PT3/8 port locations of other standard profile cylinders. The integrated -S magnet also allows you to drop in AirTAC CMSE or DMSE sensors for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X160S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.