Airtac SE80 Standard Cylinder SE80X165S
The AirTAC Airtac SE80 Standard Cylinder SE80X165S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 165mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke165 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X165S
The AirTAC SE80X165S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies sensor placement along three integrated grooves. Equipped with a -S magnet, this unit interfaces directly with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection.
Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, absorbing kinetic energy smoothly rather than relying on a fixed rubber bumper. With an 80 mm bore, a 25 mm piston rod, and PT3/8 ports, it is tailored for heavy-duty positioning tasks operating between 30-800 mm/s.
Airtac SE80 Standard Cylinder SE80X165S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X165S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X165S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X165S Is Used
Press Die Ejection
Provides 2513 N of extend force at 0.5 MPa to positively eject heavy stamped metal panels from progressive press dies, utilizing the 165 mm stroke to clear the lower shoe.
Pallet Diverting Arm
Swings a heavy-duty deflector plate on a packaging line to route loaded pallets, relying on the 25 mm rod to withstand high lateral inertia during the 165 mm swing arc.
Injection Mold Clamping
Secures the core side of a mid-size injection mold against 0.7 MPa hydraulic pressure, using the 3518 N push force and the -S magnet to confirm mold closure via DMSE sensors.
Is the Airtac SE80 Standard Cylinder SE80X165S the Right Cylinder?
Selecting the SE80X165S makes sense when your fixture requires substantial thrust without stepping up to the largest available bores. If you need slightly less force, stepping down to the 63 mm bore drops the 0.5 MPa push to 1559 N. Conversely, escalating to the 100 mm bore raises that same 0.5 MPa push to 3927 N. Because this is a 165 mm stroke, the 25 mm rod handles moderate side loads well, though any heavy off-center payload should still rely on an external guide rail to prevent rod-bearing wear.
As a dimensionally interchangeable ISO 15552 cylinder, this model serves as a direct drop-in replacement for other 80 mm profile cylinders, matching standard mounting centers for FA, FB, LB, and TC accessories. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load vertically if air pressure is lost. For position holding, consider the BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X165S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force increases to 3518 N. The maximum push force is 513 kgf when operated at the 1.0 MPa pressure limit.
No, the adjustable air cushion at both ends only decelerates the piston near the stroke limits; it does not act as a brake or lock. If the air supply is lost or the valve is centered, the cylinder will drift. For load holding, you need the BSE variant with a rod lock or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X165S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.