Airtac SE80 Standard Cylinder SE80X1700S
The AirTAC Airtac SE80 Standard Cylinder SE80X1700S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 1700mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke1700 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X1700S
The AirTAC SE80X1700S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It delivers 2513 N of push force at 0.5 MPa and features a substantial 1700 mm stroke. Because this stroke exceeds the 1500 mm standard maximum, it is manufactured as a made-to-order component to fit your extended travel requirements.
The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush while exposing sensor grooves on three sides. The integrated -S magnet supports CMSE reed and DMSE electronic position switches for precise end-of-stroke detection, while the field-adjustable air cushioning at both ends allows you to tune end-stop deceleration for heavy payloads.
Airtac SE80 Standard Cylinder SE80X1700S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X1700S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 1700 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X1700S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×1700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X1700S Is Used
Automotive Body Panel Press
Provides 2513 N of push at 0.5 MPa to position heavy sheet metal blanks into large forming presses over its 1700 mm travel.
Pallet Accumulation Gate
Actuates a diverter arm across a wide 1700 mm conveyor belt, using its built-in magnet and DMSE sensor to confirm gate open/close positions.
Lumber Sorting Pusher
Sweeps cut timber boards from a high-speed planer line into downstream grading bays, relying on adjustable pneumatic cushions to soften the long-stroke end stops.
Is the Airtac SE80 Standard Cylinder SE80X1700S the Right Cylinder?
At 0.5 MPa, this 80 mm bore generates 2513 N of push force. If your application requires less thrust, the 63 mm bore offers 1559 N; if you need more power, the 100 mm bore provides 3927 N. This cylinder uses a PT3/8 port, M20x1.5 rod thread, and a built-in magnet for CMSE or DMSE sensors.
Because the 1700 mm stroke is non-standard and exceeds the 1500 mm maximum, expect made-to-order lead times. At this extended length, the 25 mm rod is highly susceptible to bending under lateral loads; you must use an external guide to prevent rod-bearing damage. Remember that standard air cushions only decelerate the piston near stroke end and will not hold a load if air pressure drops.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X1700S FAQ
This 80 mm bore cylinder generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. The 1700 mm stroke exceeds the 1500 mm standard maximum, making it a non-standard, made-to-order configuration.
Yes, the SE80X1700S is dimensionally interchangeable with other ISO 15552 profile cylinders and shares standardized mounting interfaces. The built-in -S magnet works seamlessly with AirTAC CMSE reed and DMSE electronic sensors, and its adjustable end cushions can be field-tuned to match existing machine dynamics.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X1700S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.