Airtac SE80 Standard Cylinder SE80X1750S
The AirTAC Airtac SE80 Standard Cylinder SE80X1750S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 1750mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke1750 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X1750S
The AirTAC SE80X1750S is a double-acting, single-rod ISO 15552 profile cylinder engineered for long-reach linear motion. It features an 80 mm bore that generates 2513 N of push force at 0.5 MPa and includes a built-in magnet for position sensing. Because the 1750 mm stroke exceeds the standard 1500 mm maximum, this unit is provided as a non-standard, made-to-order configuration.
The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight spaces. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, softening hard impacts when moving heavy loads at high speeds.
Airtac SE80 Standard Cylinder SE80X1750S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X1750S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 1750 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X1750S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×1750 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X1750S Is Used
Automated Pallet Transfer
Pushes heavy loaded pallets along a 1.75 m conveyor line, utilizing the 2513 N push force to overcome initial static friction without stalling.
Large Carton Erecting
Extends to fold and erect oversized corrugated cartons on a high-speed packaging line, relying on the DMSE electronic sensor to confirm full extension.
Vertical Lift Gate Actuation
Raises and lowers a 1.75 m vertical loading dock gate, using the adjustable end cushions to prevent slamming at the top of the stroke.
Is the Airtac SE80 Standard Cylinder SE80X1750S the Right Cylinder?
When sizing this actuator, consider stepping down to a 63 mm bore (1559 N push at 0.5 MPa) for lighter loads, or up to a 100 mm bore (3927 N push at 0.5 MPa) if your application requires greater thrust. As a true ISO 15552 profile cylinder, this model serves as a drop-in replacement for other ISO 15552 cylinders, sharing standard mounting accessories like FA front flanges or TC center trunnions.
Because the 1750 mm stroke is exceptionally long, the 25 mm rod and internal bearing face significant bending moments under side loads; an external guide rail is strongly recommended to prevent premature seal wear. Note that the standard pneumatic cushion only decelerates the piston near stroke end—it does not lock or hold the load. If your process requires position holding without live air pressure, integrate a BSE rod lock or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X1750S FAQ
This 80 mm bore cylinder uses a PT3/8 port. At 0.5 MPa it provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa the push force is 3518 N, and the maximum push force is 513 kgf at 1.0 MPa.
Yes, the SE80X1750S is dimensionally interchangeable with other ISO 15552 profile cylinders. It shares the standardized mounting interface and utilizes a PT3/8 port, allowing you to reuse existing FA, FB, or TC mounting hardware without modifying the machine frame.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X1750S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.