Airtac SE80 Standard Cylinder SE80X175H
The AirTAC Airtac SE80 Standard Cylinder SE80X175H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 175mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke175 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X175H
The AirTAC SE80X175H is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature pneumatic tasks. Delivering a robust 2513 N push force at 0.5 MPa, it utilizes a 25 mm hard-chrome rod with an M20x1.5 thread. The square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant body that simplifies mounting in tight machinery spaces.
Equipped with a Viton (FKM) seal, this specific unit reliably operates in ambient temperatures up to 150 C, far exceeding standard elastomer limits. The field-adjustable pneumatic cushioning at both stroke ends allows technicians to fine-tune end-of-travel deceleration, softening hard impacts during high-speed 30-800 mm/s operations. Note this SKU lacks a built-in position magnet.
Airtac SE80 Standard Cylinder SE80X175H Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X175H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 175 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X175H
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X175H Is Used
Thermoforming Mold Clamping
Secures heated plastic sheets during molding cycles, utilizing the 2513 N push force and FKM seal to withstand 150 C ambient radiant heat without degrading.
Hot Extrusion Diversion
Actuates routing gates on conveyor lines transferring freshly extruded warm profiles, relying on the 175 mm stroke and high-temp Viton elastomer for reliable shifting.
Engine Bay Component Ejection
Ejects cast automotive parts from heated fixtures, where the 3518 N push at 0.7 MPa breaks draft friction and the FKM seal resists thermal aging.
Is the Airtac SE80 Standard Cylinder SE80X175H the Right Cylinder?
Selecting this 80 mm bore yields 2513 N of push at 0.5 MPa. If your assembly requires less force, the 63 mm neighbor provides 1559 N; conversely, stepping up to the 100 mm bore delivers 3927 N for heavier payloads. Because this 175 mm stroke is under the 300 mm threshold, side-load stress on the rod bearing is minimal, though long unsupported loads still necessitate an external guide. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct drop-in replacement for other standard profile cylinders, matching the PT3/8 port and basic mounting footprint. Remember that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure is lost. For position holding, consider the BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X175H FAQ
This 80 mm bore cylinder provides 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. Equipped with an FKM seal, it operates in environments up to 150 C.
Yes, the SE80X175H is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing mounts matching the PT3/8 port and 80 mm footprint, though it lacks a position sensor magnet for reed or electronic switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X175H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.