Airtac SE80 Standard Cylinder SE80X180
The AirTAC Airtac SE80 Standard Cylinder SE80X180 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 180mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke180 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X180
The AirTAC SE80X180 is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a robust 2513 N push force at 0.5 MPa. Its square extruded aluminum barrel omits external tie rods, yielding a highly compact footprint that resists corrosion and mounts flush against machine frames.
This 80 mm bore unit features field-adjustable air cushioning at both ends, allowing technicians to fine-tune end-of-stroke deceleration via a set screw rather than relying on fixed rubber bumpers. This specific SKU lacks the built-in magnet option, meaning it is optimized for pure drive power without position sensing.
Airtac SE80 Standard Cylinder SE80X180 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X180 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 180 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X180
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×180 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X180 Is Used
Palletizer Flap Control
Drives the heavy flap mechanisms on medium-duty palletizers, utilizing the 2513 N push force to snap heavy cardboard corrugated flaps into position for automated strapping.
Bottling Line Diverter
Actuates high-speed lane diverters on bottling conveyors, where the adjustable end cushions soften the 180 mm stroke transitions to prevent glass container tipping at high speeds.
Injection Mold Ejection
Provides the primary push-off force for ejecting dense plastic automotive interior panels from injection molds, relying on the 25 mm hard-chrome rod to handle high side-load stress.
Is the Airtac SE80 Standard Cylinder SE80X180 the Right Cylinder?
Stepping down to the 63 mm bore reduces the 0.5 MPa push output to 1559 N, whereas moving up to the 100 mm bore increases it to 3927 N, allowing you to scale exactly to your load requirements. Because this is a standard double-acting cylinder, it cannot hold a load if air pressure is lost; if your application requires static position holding, you must integrate an external BSE rod lock or pilot-operated check valve. To retrofit this into an existing setup, match the 180 mm stroke, PT3/8 port, and standard ISO 15552 mounting accessories. Since the stroke is 180 mm, ensure the 25 mm rod and its bearing can handle any lateral deflection by adding an external guide for heavy offset loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X180 FAQ
The SE80X80 delivers 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. It uses a PT3/8 port and features a 25 mm rod with an M20x1.5 thread.
Yes, the SE80X180 is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing machine designs and reuse standard ISO mounting hardware without modifying the frame, though this specific SKU lacks a sensor magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X180
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.