Airtac SE80 Standard Cylinder SE80X200H
The AirTAC Airtac SE80 Standard Cylinder SE80X200H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 200mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke200 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X200H
The AirTAC SE80X200H is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature actuation. Delivering a robust 2513 N push force at 0.5 MPa, it is built around a square extruded aluminum barrel that omits external tie rods. This clean-profile design resists corrosion and allows flush mounting in tight machinery frames, while the standardized ISO 15552 mounting interface ensures a true drop-in retrofit for existing global cylinder footprints.
This 80 mm bore unit features a 200 mm stroke and a Viton (FKM) seal rated for continuous duty up to 150 C. The field-adjustable pneumatic cushioning at both ends uses a precision screw to tailor end-of-stroke deceleration, absorbing kinetic energy to prevent hard mechanical impacts. Note this specific SKU lacks a built-in magnet, so external position sensing is not supported without modification.
Airtac SE80 Standard Cylinder SE80X200H Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X200H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X200H
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X200H Is Used
Plastic Injection Mold Extraction
Provides the 2513 N push force required to eject dense plastic parts from hot molds, utilizing the Viton seal to withstand ambient radiated heat up to 150 C.
Hot-Melt Packaging Sealing
Drives sealing platens on continuous-flow packaging lines where the FKM seal survives thermal exposure from adjacent glue applicators while cycling at 30-800 mm/s.
Metal Stamping Ejection
Kicks stamped sheet metal blanks out of progressive dies, relying on the 36 mm adjustable cushion to soften end-stops under high kinetic loads.
Is the Airtac SE80 Standard Cylinder SE80X200H the Right Cylinder?
Stepping down from this 80 mm bore, the 63 mm variant yields 1559 N of push force at 0.5 MPa, whereas stepping up to the 100 mm bore provides 3927 N. Use the SE80X200H when your load demands the 2513 N (0.5 MPa) output alongside elevated ambient heat. Because the adjustable air cushion only decelerates the piston near the stroke end, it cannot hold a load if air pressure drops; applications requiring true mid-stroke position holding without live pressure should pivot to the BSE rod-lock variant. To match this cylinder for an ISO 15552 replacement, confirm the 200 mm stroke, PT3/8 port, and required mounting bracket.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X200H FAQ
The SE80X200H generates 2513 N of push force and 2268 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 3518 N. The maximum rated push force is 513 kgf when operated at the 1.0 MPa pressure limit.
Yes. The SE80X200H is dimensionally interchangeable per ISO 15552 standards, meaning it shares the exact same mounting footprint and PT3/8 port size as other ISO 15552 profile cylinders. You can drop it in as a direct replacement for standard hardware.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X200H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.