Airtac SE80 Standard Cylinder SE80X200S
The AirTAC Airtac SE80 Standard Cylinder SE80X200S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 200mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke200 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X200S
The AirTAC SE80X200S is a double-acting, single-rod ISO 15552 profile cylinder featuring an 80 mm bore and 200 mm stroke. It delivers a robust 2513 N push force at 0.5 MPa, extending to 3518 N at 0.7 MPa. The extruded aluminum barrel design omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized mounting interfaces on multiple sides.
Equipped with a built-in magnet (the -S option), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows you to tune end-cap deceleration, softening hard mechanical stops during high-speed actuation up to 800 mm/s.
Airtac SE80 Standard Cylinder SE80X200S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X200S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X200S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X200S Is Used
Corrugated Box Folder
Drives the folding flaps on a high-speed packaging line, utilizing the 2513 N push force to cleanly crease heavy cardboard at 200 mm stroke.
Pallet Diverter Arm
Actuates a routing gate on a conveyor system, relying on the built-in magnet to trigger DMSE sensors for confirming the 200 mm extend position.
Injection Mold Ejector
Pushes finished plastic parts out of an injection molding die, where the adjustable cushion softens the 800 mm/s impact at end-of-stroke.
Is the Airtac SE80 Standard Cylinder SE80X200S the Right Cylinder?
Choosing this 80 mm bore makes sense when your load requires approximately 2513 N of thrust at 0.5 MPa. If your application demands less force, stepping down to the 63 mm bore yields 1559 N push, saving space and air consumption. Conversely, if you need higher capacity, the 100 mm bore provides 3927 N push. Because this is a double-acting cylinder, it relies on continuous air pressure to hold position; if pneumatic supply drops, the piston will drift, so a BSE rod lock variant is necessary for fail-safe holding.
As a standard ISO 15552 cylinder, the SE80X200S serves as a drop-in dimensional replacement for other ISO 15552 profile cylinders, sharing identical mounting footprints and PT3/8 port locations. The 200 mm stroke falls below the 1500 mm maximum standard, but any stroke over 300 mm introduces rod-bearing bending moments under lateral loads. For long pushes, incorporate an external guide rail to prevent side-load damage to the M20x1.5 rod thread and internal seals.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X200S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force increases to 3518 N. The absolute maximum push capacity is 513 kgf when operating at the maximum rated pressure of 1.0 MPa.
Yes, the SE80X200S is dimensionally interchangeable per ISO 15552 standards. It shares the exact same mounting interface and PT3/8 port locations as other ISO 15552 profile cylinders, allowing a direct drop-in retrofit without altering your machine's mounting holes.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X200S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.