Airtac SE80 Standard Cylinder SE80X220S
The AirTAC Airtac SE80 Standard Cylinder SE80X220S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 220mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke220 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X220S
The AirTAC SE80X220S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics, delivering 2513 N of push force at 0.5 MPa and up to 513 kgf at 1.0 MPa. Its extruded aluminum barrel lacks external tie rods, yielding a flush, corrosion-resistant exterior that simplifies direct mounting and minimizes debris buildup in aggressive production zones.
This 80mm bore, 220mm stroke unit includes a built-in magnet (-S) for non-contact position sensing via AirTAC CMSE reed or DMSE electronic switches seated in the three-sided sensor groove. Field-adjustable pneumatic cushioning at both ends allows mechanics to dial in end-of-stroke deceleration, softening hard impacts during high-speed 30-800 mm/s cycles.
Airtac SE80 Standard Cylinder SE80X220S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X220S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 220 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X220S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×220 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X220S Is Used
CNC Lathe Chuck Actuation
Provides the 2513 N push force required to securely close heavy-duty pneumatic chucks on steel bar stock during automated CNC turning cycles.
Pallet Diverters
Leverages the 220 mm stroke to extend diverter arms across wide roller conveyors, reliably redirecting heavy loaded pallets at high speeds.
Corrugated Box Forming
Drives the folding plows on heavy corrugated cardboard box erectors, utilizing the adjustable end cushions to soften the stroke during rapid 30-800 mm/s operation.
Is the Airtac SE80 Standard Cylinder SE80X220S the Right Cylinder?
Selecting this 80mm bore cylinder makes sense when your mechanism requires the 2513 N push at 0.5 MPa that the SE80 provides. If your load is lighter, stepping down to the 63mm bore drops the output to 1559 N, whereas moving up to the 100mm bore increases it to 3927 N, giving you a clear sizing path either way. Because the stroke is 220 mm, the 25 mm rod and M20x1.5 thread will experience bending moments under heavy transverse loads; always support the mechanism with an external linear guide to prevent premature rod-bearing wear. As a true ISO 15552 profile cylinder, it offers a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standard mounting accessories and PT3/8 ports. Note that if your process demands fail-safe load holding without constant air pressure, you must add an external rod lock or pilot-operated check valve, as the adjustable cushion only decelerates the piston and cannot hold a stationary load.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X220S FAQ
The 80mm bore provides a push force of 2513 N and a pull force of 2268 N at 0.5 MPa. At 0.7 MPa, the push force is 3518 N, with a maximum push of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X220S is dimensionally interchangeable per ISO 15552 standards, meaning it shares the same mounting footprint and PT3/8 port locations. You can drop it into existing machinery designs, and the built-in -S magnet works seamlessly with AirTAC CMSE and DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X220S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.