Airtac SE80 Standard Cylinder SE80X225S
The AirTAC Airtac SE80 Standard Cylinder SE80X225S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 225mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke225 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X225S
The AirTAC SE80X225S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 2513 N of push force at 0.5 MPa. Driven by a Ø25 mm piston rod with an M20x1.5 thread, this unit handles a 225 mm stroke and operates at speeds from 30-800 mm/s. Because the stroke exceeds the 1500 mm standard maximum for this bore, it is supplied as a made-to-order configuration.
The extruded aluminum barrel lacks external tie rods, yielding a smooth, corrosion-resistant profile that mounts flush in tight machine spaces. Equipped with a built-in magnet (-S), the cylinder integrates seamlessly with AirTAC CMSE reed and DMSE electronic sensors for precise end-position detection across three available sensor grooves.
Airtac SE80 Standard Cylinder SE80X225S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X225S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 225 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X225S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X225S Is Used
Press Brake Tooling
Provides the 2513 N push force required to position and hold backgauges on heavy sheet metal press brakes.
Pallet Diverters
Utilizes the 225 mm stroke and built-in DMSE sensor magnet to actuate diverting arms on 1200 mm wide roller conveyors.
Corrugated Box Folding
Leverages the smooth tie-rod-free profile and adjustable pneumatic cushions to cleanly fold heavy corrugated flaps without denting the board.
Is the Airtac SE80 Standard Cylinder SE80X225S the Right Cylinder?
If your application requires less force, stepping down to a 63 mm bore yields a 1559 N push at 0.5 MPa, whereas scaling up to a 100 mm bore provides a 3927 N push. The SE80X225S is dimensionally interchangeable per ISO 15552, allowing a direct drop-in retrofit for other ISO 15552 cylinders using standardized mounting hardware and a PT3/8 port.
Because this unit features a 225 mm stroke, the unsupported rod length increases bending moments on the rod bearing; for heavy lateral loads, implement an external guide to prevent premature wear. Note that the field-adjustable air cushion at both ends only decelerates the piston near stroke end and does not hold the load if air pressure is lost—use a BSE rod lock for static holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X225S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force is 3518 N, with a maximum push of 513 kgf at 1.0 MPa. It uses a PT3/8 port, a Ø25 mm rod, and an M20x1.5 rod-end thread.
Yes, the SE80X225S shares the exact ISO 15552 mounting interface, making it dimensionally interchangeable with other ISO 15552 profile cylinders. The built-in magnet also allows drop-in compatibility with AirTAC CMSE and DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X225S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.