Airtac SE80 Standard Cylinder SE80X430S
The AirTAC Airtac SE80 Standard Cylinder SE80X430S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 430mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke430 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X430S
The AirTAC SE80X430S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 2513 N of push force at 0.5 MPa. With a 430 mm stroke and PT3/8 porting, it fits heavy-duty motion cycles seamlessly.
Its square extruded aluminum barrel omits external tie rods, yielding a flush, corrosion-resistant exterior that simplifies flush mounting. The integrated -S magnet enables position detection via CMSE reed or DMSE electronic sensors, while the field-adjustable air cushioning at both ends lets you fine-tune end-of-stroke deceleration to protect heavy payloads.
Airtac SE80 Standard Cylinder SE80X430S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X430S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 430 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X430S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×430 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X430S Is Used
Palletizer Case Pusher
Drives large cardboard cartons onto pallets at 2513 N push, using the 430 mm stroke to clear the conveyor lane completely.
Press Brake Demolder
Strips heavy formed sheet metal blanks from press brake dies, leveraging the 513 kgf max push to break vacuum suction cups.
Injection Mold Ejector
Kicks finished plastic parts out of injection molds, relying on the adjustable pneumatic cushion to soften the 430 mm retraction stop.
Is the Airtac SE80 Standard Cylinder SE80X430S the Right Cylinder?
If 2513 N push at 0.5 MPa is too much, the 63 mm bore offers 1559 N; if you need more force, the 100 mm bore provides 3927 N. Because this is a 430 mm stroke, the 25 mm rod and M20x1.5 thread face bending stresses under side loads—an external guide is strongly recommended to prevent rod-bearing wear. Remember, a plain SE cylinder drifts if air pressure is lost; use a BSE rod lock for position holding. This model is dimensionally interchangeable per ISO 15552, accepting standard mounting accessories and sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X430S FAQ
At 0.5 MPa, the SE80X430S provides 2513 N push and 2268 N pull. At 0.7 MPa, it pushes 3518 N. The maximum push force is 513 kgf at 1.0 MPa, and the 430 mm stroke falls within the 1500 mm standard limit for this 80 mm bore.
Yes, the SE80X430S is dimensionally interchangeable per ISO 15552. You can swap it directly with other ISO 15552 cylinders using identical mounting hardware. The included -S magnet also works directly with AirTAC CMSE and DMSE sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X430S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.