Airtac SE80 Standard Cylinder SE80X475S
The AirTAC Airtac SE80 Standard Cylinder SE80X475S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 475mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke475 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X475S
The AirTAC SE80X475S is a double-acting single-rod ISO 15552 profile cylinder featuring an 80 mm bore and a 475 mm stroke. It delivers a substantial 2513 N push force at 0.5 MPa, making it well-suited for heavy-duty positioning tasks. The extruded aluminum barrel omits external tie rods, yielding a smooth, corrosion-resistant body that mounts flush against machine frames while freeing up adjacent space for valves and manifolds.
Equipped with a built-in magnet (S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated side grooves. Field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration via a simple screw, softening hard mechanical impacts during high-speed actuation.
Airtac SE80 Standard Cylinder SE80X475S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X475S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 475 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X475S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×475 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X475S Is Used
Pallet Transfer Diverter
Harnessing 2513 N of push force at 0.5 MPa to reliably shove heavy loaded pallets onto perpendicular packaging roller lines.
Injection Mold Ejection
Uses the 475 mm stroke to reach deep into a press and extract large automotive interior panels without binding the mold.
Stamping Press Feed
Pushes heavy coil steel strips into a mechanical stamping press, relying on the smooth tie-rod-free barrel for flush mounting.
Is the Airtac SE80 Standard Cylinder SE80X475S the Right Cylinder?
When sizing this 80 mm bore actuator, consider stepping down to a 63 mm model if your load requires less than 1559 N push at 0.5 MPa, or stepping up to a 100 mm bore if you need to exceed 3927 N. Because the 475 mm stroke creates a long lever arm, side loads can induce severe bending moments on the Ø25 mm rod and front bearing; always support the load with an external guide rail to prevent premature seal wear. As a standard ISO 15552 cylinder, it serves as a dimensionally interchangeable drop-in replacement for other ISO 15552 profile cylinders, matching the PT3/8 port, 475 mm stroke, and standard mounting accessories. Note that the adjustable air cushion only decelerates the piston near stroke end and will not hold a load if air pressure is lost.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X475S FAQ
At 0.5 MPa, the 80 mm bore provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, push increases to 3518 N. The maximum push force is 513 kgf at 1.0 MPa, and the operational speed range is 30-800 mm/s.
No, the adjustable air cushion only decelerates the piston near the end of the stroke and acts as a bumper, not a mechanical lock. The cylinder will drift if air pressure drops or the valve is centered. For positive load holding, consider an AirTAC BSE series rod lock cylinder or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X475S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.