Airtac SE80 Standard Cylinder SE80X480S
The AirTAC Airtac SE80 Standard Cylinder SE80X480S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 480mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke480 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X480S
The AirTAC SE80X480S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa. It features an 80 mm bore and a 480 mm stroke, making it well-suited for heavy-duty industrial actuation.
This model includes a built-in magnet for CMSE and DMSE position sensing. The extruded aluminum barrel design omits external tie rods, offering a flush exterior that resists dirt accumulation and simplifies direct mounting, while the field-adjustable air cushions at both ends allow you to fine-tune end-of-stroke deceleration for high-speed cycles.
Airtac SE80 Standard Cylinder SE80X480S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X480S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 480 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X480S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×480 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X480S Is Used
Injection Mold Clamping
Provides 2513 N of push force at 0.5 MPa to secure injection mold tooling plates during the injection cycle.
Pallet Diverting Arm
Uses the 480 mm stroke to extend a heavy diverter arm across a wide packaging conveyor for high-throughput logistics.
Press Brake Forming
Applies up to 513 kgf at 1.0 MPa to actuate the upper beam of a small pneumatic press brake for sheet metal bending.
Is the Airtac SE80 Standard Cylinder SE80X480S the Right Cylinder?
If your application requires less force, the 63 mm bore provides a 1559 N push at 0.5 MPa, whereas stepping up to the 100 mm bore yields a 3927 N push. The 480 mm stroke on this 80 mm bore is well within the 1500 mm maximum standard stroke limit, so it ships as a standard catalog item.
Because the stroke exceeds 300 mm, the extended rod is susceptible to bending under lateral loads; an external guide rail should be used to prevent side-load damage to the M20x1.5 rod thread and front bearing. This plain SE cylinder will drift if air pressure is lost or the valve is centered, so a BSE rod lock is required if the load must be held in place.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X480S FAQ
At 0.5 MPa, the push force is 2513 N and the pull force is 2268 N. At 0.7 MPa, the push force is 3518 N. The maximum push force is 513 kgf at 1.0 MPa.
Yes, the SE80X480S is dimensionally interchangeable per ISO 15552 standards, allowing it to drop-in replace other ISO 15552 cylinders using the same PT3/8 port and mounting hardware.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X480S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.