Airtac SE80 Standard Cylinder SE80X500S
The AirTAC Airtac SE80 Standard Cylinder SE80X500S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 500mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke500 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X500S
The AirTAC SE80X500S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa. Its extruded aluminum barrel design omits external tie rods, yielding a compact, flush-mounting body that naturally resists corrosion and simplifies fixture integration. A built-in magnet (-S) comes standard, enabling precise end-position detection with AirTAC CMSE reed or DMSE electronic sensors.
Equipped with a 25 mm piston rod and PT3/8 ports, this 80 mm bore unit manages a 500 mm stroke while operating at speeds of 30-800 mm/s. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration, effectively softening hard impacts during high-speed cycles. This is a true dampening system, not a static rubber bumper.
Airtac SE80 Standard Cylinder SE80X500S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X500S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X500S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X500S Is Used
Pallet Diversion Gate
Leveraging 2513 N of push force at 0.5 MPa to reliably divert heavy timber pallets across high-speed packaging lines without stalling.
Corrugated Box Flap Folder
Utilizes the 500 mm stroke to extend across wide-format carton erectors, folding large corrugated side flaps smoothly at cycle rates up to 800 mm/s.
Automotive Press Ejector
Ejects stamped metal body panels from hydraulic presses, using the adjustable end cushions to prevent part marring during rapid retraction.
Is the Airtac SE80 Standard Cylinder SE80X500S the Right Cylinder?
Selecting the SE80X500S is ideal when your application requires substantial thrust over a long reach. If you need less force, stepping down to the 63 mm bore drops the 0.5 MPa push output to 1559 N, whereas stepping up to the 100 mm bore increases it to 3927 N for heavier loads. Because this model features a 500 mm stroke, the extended rod is subject to bending moments under side loads; always pair it with an external guide rail to prevent premature rod-bearing wear.
As a genuine ISO 15552 profile cylinder, it provides drop-in dimensional interchangeability with other ISO 15552 cylinders, allowing you to retrofit existing setups without altering mounting hardware. Note that a standard double-acting cylinder drifts when air pressure is lost or the valve is centered; if your process demands fail-safe load holding, consider the AirTAC BSE rod-lock variant or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X500S FAQ
At 0.5 MPa, the SE80X500S provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force reaches 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The operating speed ranges from 30-800 mm/s.
Yes. The SE80X500S is dimensionally interchangeable with any standard ISO 15552 profile cylinder. It shares the exact same mounting interface and PT3/8 port locations, allowing for a direct drop-in replacement without machining new mounting holes.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X500S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.