Airtac SE80 Standard Cylinder SE80X500SH
The AirTAC Airtac SE80 Standard Cylinder SE80X500SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 500mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke500 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X500SH
The AirTAC SE80X500SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It generates 2513 N of push force at 0.5 MPa and integrates a built-in magnet for position sensing. The square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with high-temperature FKM (Viton) seals, this 80 mm bore unit operates reliably in thermal environments up to 150 C. Field-adjustable pneumatic cushioning at both stroke ends allows you to tune end-of-stroke deceleration via a set screw, protecting payloads from hard mechanical impacts during high-speed cycling.
Airtac SE80 Standard Cylinder SE80X500SH Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X500SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 500 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X500SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X500SH Is Used
Injection Mold Extraction
Survives 150 C ambient heat near mold platens using FKM seals, applying 2513 N of push force to eject hot plastic automotive interior panels.
Bottling Line Diverters
Uses the integrated magnet with DMSE sensors to confirm full 500 mm extension, reliably routing heavy glass beverage crates at high cycling speeds.
Metal Stamping Feed
Pushes coiled steel blanks into a stamping press, relying on adjustable end cushions to soften the 3518 N dynamic impact at 0.7 MPa operating pressure.
Is the Airtac SE80 Standard Cylinder SE80X500SH the Right Cylinder?
Selecting this 80 mm bore provides 2513 N of thrust at 0.5 MPa, bridging the gap between the 63 mm bore (1559 N push) and the 100 mm bore (3927 N push). The PT3/8 port and 25 mm rod handle significant flow and side loads, but at 500 mm of stroke, unsupported rod-bearing bending increases; integrate an external guide rail to prevent premature seal wear. The FKM seal makes it ideal for hot processes, while the -S magnet pairs directly with CMSE reed and DMSE electronic sensors.
Because it adheres to the ISO 15552 / VDMA 24562 dimensional standard, this cylinder serves as a drop-in replacement for other ISO 15552 profile cylinders without requiring custom mounting plates. Note that a standard SE does not hold loads unpowered—air loss causes piston drift; specify a BSE variant if mid-stroke locking is required.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X500SH FAQ
At 0.5 MPa, this 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force reaches 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. It operates at speeds of 30-800 mm/s.
No, the adjustable air cushion only decelerates the piston near the stroke ends and does not lock the rod. If the valve centers or air is lost, the load will drift. For true position holding, use a BSE rod-lock variant or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X500SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.