Airtac SE80 Standard Cylinder SE80X50H
The AirTAC Airtac SE80 Standard Cylinder SE80X50H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 50mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke50 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X50H
The AirTAC SE80X50H is a double-acting single-rod ISO 15552 profile cylinder engineered for high-temperature tasks. It generates 2513 N of push force and 2268 N of pull force at 0.5 MPa, extending to 3518 N push at 0.7 MPa. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against frames while resisting mechanical snagging in tight machine cells.
This specific SKU features an FKM (Viton) seal, widening the operating temperature range from -20 C up to 150 C for thermal-heavy environments. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-of-stroke deceleration via a setscrew, softening hard impacts without relying on fixed rubber bumpers. Note that this configuration lacks a built-in sensor magnet, so position detection requires external proximity switches.
Airtac SE80 Standard Cylinder SE80X50H Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X50H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X50H
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X50H Is Used
Plastic Injection Mold Extraction
Withstands radiant heat up to 150 C via FKM seals while providing 2513 N push at 0.5 MPa to eject hot plastic automotive interior panels.
Shrink Wrap Sealing Jaws
Handles the thermal exposure near heat tunnels, using its 50 mm stroke and adjustable end cushions to gently close sealing bars without impact.
Aluminum Die Casting Extraction
Survives ambient heat near molten metal pits, delivering 3518 N push at 0.7 MPa to pull hot cast engine housings from dies.
Is the Airtac SE80 Standard Cylinder SE80X50H the Right Cylinder?
When sizing this 80 mm bore actuator, evaluate your thrust requirements against its neighbors. If 2513 N push at 0.5 MPa is excessive, stepping down to the 63 mm bore trims output to 1559 N. Conversely, if your load demands more power, the 100 mm bore raises push capacity to 3927 N. Remember that a standard SE cylinder drifts when air pressure is removed or a valve centers; it cannot hold a vertical load statically, so integrate an external rod lock or pilot-operated check valve for fail-safe holding. Because this is a 50 mm stroke, side-loading on the M20x1.5 rod thread is minimal, though an external guide remains best practice for offset loads. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct retrofit for other 80 mm profile cylinders using identical PT3/8 port and standard mounting hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X50H FAQ
The SE80X50H generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum of 513 kgf at 1.0 MPa. It uses a PT3/8 port, a 25 mm rod, and an M20x1.5 rod-end thread.
Yes, its extruded profile body is dimensionally interchangeable with any standard ISO 15552 cylinder, allowing drop-in retrofits using shared mounting accessories. The H code denotes an FKM (Viton) seal, extending the thermal limit to 150 C for high-temperature environments.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X50H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.