Airtac SE80 Standard Cylinder SE80X510S
The AirTAC Airtac SE80 Standard Cylinder SE80X510S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 510mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke510 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X510S
The AirTAC SE80X510S is a double-acting single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It generates 2513 N of push force and 2268 N of pull force at 0.5 MPa, utilizing a 25 mm piston rod and a PT3/8 port. The 510 mm stroke falls within standard manufacturing limits, making it immediately suitable for long-travel automation tasks.
Built with a square extruded aluminum barrel that eliminates external tie rods, this cylinder offers a flush, corrosion-resistant exterior that mounts cleanly in tight spaces. The integrated -S magnet enables precise end-position detection using AirTAC CMSE reed or DMSE electronic sensors. Furthermore, the field-adjustable air cushioning at both ends allows technicians to dial in the exact deceleration required to soften hard end stops at high cycling speeds.
Airtac SE80 Standard Cylinder SE80X510S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X510S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 510 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X510S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×510 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X510S Is Used
Pallet Transfer Diversion
Leverages the 510 mm stroke to push heavy timber pallets off a high-throughput main conveyor line onto a secondary packaging spur.
Corrugated Box Flap Folding
Applies 2513 N of push force at 0.5 MPa to cleanly fold and hold heavy corrugated cardboard flaps during automated hot-melt gluing cycles.
Injection Mold Core Pulling
Actuates large steel core inserts in injection molding machines, utilizing the 25 mm rod and adjustable cushioning to safely extract parts without shock.
Is the Airtac SE80 Standard Cylinder SE80X510S the Right Cylinder?
Selecting the SE80X510S provides 2513 N push at 0.5 MPa, striking a balance for medium-to-heavy loads. If your application requires less force, stepping down to the 63 mm bore yields 1559 N push, while stepping up to the 100 mm bore provides 3927 N push for heavier dynamics. Because this cylinder features a 510 mm stroke, the extended rod is subject to bending moments under side loads; an external guide rail should be installed to prevent premature rod-bearing wear.
As a true ISO 15552 profile cylinder, this model is dimensionally interchangeable with other ISO 15552 cylinders, allowing drop-in retrofits without altering existing mounting hardware. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold the load; if air pressure is lost, the piston will drift. For position holding, consider a BSE rod lock variant. This unit includes the -S magnet for position sensing and uses standard PT3/8 ports.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X510S FAQ
At 0.5 MPa, the SE80X510S delivers 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X510S is dimensionally interchangeable per ISO 15552 standards. You can use it as a drop-in replacement for other ISO 15552 profile cylinders with an 80 mm bore and 510 mm stroke, utilizing the same mounting accessories and PT3/8 port spacing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X510S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.