Airtac SE80 Standard Cylinder SE80X570S
The AirTAC Airtac SE80 Standard Cylinder SE80X570S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 570mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke570 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X570S
The AirTAC SE80X570S is a double-acting single-rod profile cylinder built to the ISO 15552 standard, delivering a robust 2513 N push force at 0.5 MPa and a 3518 N push at 0.7 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while protecting internal mechanics.
Equipped with a built-in position magnet, this 80 mm bore unit seamlessly integrates with AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. The field-adjustable air cushioning at both ends allows technicians to tune the deceleration of the 570 mm stroke via a set screw, softening hard end stops and extending seal life in high-speed cycles.
Airtac SE80 Standard Cylinder SE80X570S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X570S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 570 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X570S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×570 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X570S Is Used
Pallet Diverting Gate
Actuates a heavy diverting arm on a 1200 mm wide packaging conveyor, using the 570 mm stroke to fully extend and push 40 kg pallets onto a side lane with 2513 N of force.
CNC Lathe Bar Feeder
Drives a pusher carriage to load 65 mm steel bars into a lathe spindle, relying on the 80 mm bore and adjustable end cushions to absorb the kinetic energy of the heavy stock.
Automated Storage Crane
Shifts a vertical lifting fork assembly 570 mm outward to retrieve totes from high-density shelving, using the integrated magnet for DMSE sensor feedback at end positions.
Is the Airtac SE80 Standard Cylinder SE80X570S the Right Cylinder?
Selecting the SE80X570S provides 2513 N of push at 0.5 MPa. If your application requires less force, stepping down to the 63 mm bore yields 1559 N, while moving up to the 100 mm bore provides 3927 N. Because this cylinder features a 570 mm stroke, the extended 25 mm rod and bearing face increased bending moments under side loads; always use an external guide rail to prevent premature seal wear and piston drift.
As a standard ISO 15552 profile cylinder, this model is dimensionally interchangeable with other ISO 15552 cylinders, allowing drop-in retrofits without altering mounting hole patterns. It features a PT3/8 port, an M20x1.5 rod thread, and a built-in magnet for CMSE or DMSE sensors. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold a load; if pneumatic pressure is lost, the rod will drift, requiring a BSE rod lock for secure positioning.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X570S FAQ
At 0.5 MPa, the SE80X570S provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X570S is dimensionally interchangeable with any standard ISO 15552 cylinder. It shares the standardized 80 mm bore mounting interface and PT3/8 port locations, allowing a direct drop-in replacement without modifying your existing machine footprint.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X570S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.