Airtac SE80 Standard Cylinder SE80X600S
The AirTAC Airtac SE80 Standard Cylinder SE80X600S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 600mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke600 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X600S
The AirTAC SE80X600S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty pneumatics. It delivers a substantial 2513 N push force at 0.5 MPa and handles a maximum of 513 kgf at 1.0 MPa. The extruded aluminum barrel features a clean, square profile without external tie rods, making it highly corrosion-resistant and easy to mount flush against machine frames.
Equipped with a built-in magnet (-S), this 80mm bore unit seamlessly integrates AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection across its 600mm travel. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-stop deceleration via a set screw, softening impacts when moving heavy loads at speeds up to 800 mm/s.
Airtac SE80 Standard Cylinder SE80X600S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X600S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X600S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X600S Is Used
Pallet Transfer Line Diverter
Provides the 2513 N push at 0.5 MPa needed to reroute heavy timber pallets on a 600mm stroke diverter arm without stalling mid-cycle.
Corrugated Box Flap Folder
Uses the 80mm bore's 513 kgf maximum thrust and built-in DMSE sensor magnet to precisely fold heavy cardboard flaps at 800 mm/s.
Injection Mold Ejection Stage
Leverages the 600mm stroke and adjustable end cushions to safely extract molded plastic automotive dashboards from the press cavity.
Is the Airtac SE80 Standard Cylinder SE80X600S the Right Cylinder?
Selecting the SE80X600S makes sense when your application requires the 2513 N push at 0.5 MPa that an 80mm bore provides. If you need less force, stepping down to the 63mm bore yields 1559 N push, while stepping up to the 100mm bore provides 3927 N push for heavier payloads. Because this cylinder uses a standard ISO 15552 mounting interface, it serves as a direct drop-in replacement for other ISO 15552 cylinders, sharing standard mounting hardware and port dimensions (PT3/8).
At 600mm of stroke, the 25mm rod and M20x1.5 thread experience significant bending moments under side loads. An external guide rail is strongly recommended to prevent rod-bearing wear. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not hold a load. If air pressure drops, the piston will drift, requiring a BSE rod lock for secure positioning.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X600S FAQ
At 0.5 MPa, the 80mm bore provides 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force is 3518 N. The maximum push force is 513 kgf when operating at the 1.0 MPa pressure limit.
Yes, the SE80X600S is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders, matching the 80mm bore, 600mm stroke, PT3/8 port, and standard mounting footprint exactly.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X600S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.