Airtac SE80 Standard Cylinder SE80X700SH
The AirTAC Airtac SE80 Standard Cylinder SE80X700SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 700mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke700 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X700SH
The AirTAC SE80X700SH is a double-acting single-rod profile cylinder built to ISO 15552 and VDMA 24562 standards. It yields a 2513 N push force at 0.5 MPa and a 3518 N push at 0.7 MPa, utilizing a 25 mm rod with an M20x1.5 thread. The square extruded aluminum barrel omits external tie rods, yielding a flush-mount body that resists corrosion and simplifies sensor placement along three integrated grooves.
This specific configuration incorporates a high-temperature FKM (Viton) seal, extending the operating window from -20°C up to 150°C for hot environments. A built-in magnet (-S) enables position detection with AirTAC CMSE reed or DMSE electronic switches. Field-adjustable pneumatic cushioning at both ends allows you to tune end-of-stroke deceleration via a setscrew, softening hard impacts during the 30-800 mm/s operating speed range.
Airtac SE80 Standard Cylinder SE80X700SH Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X700SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 700 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X700SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×700 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X700SH Is Used
Injection Mold Extraction
Leverages the 2513 N extend force and 150°C FKM seals to reliably pull hot plastic parts from mold cavities without degrading the seals.
Heavy Pallet Diverter
Uses the 700 mm stroke to push heavy pallets off a high-throughput conveyor line, relying on the adjustable cushion to soften the full-stroke arrival.
Hot End Stamping Ejector
Deploys the 3518 N push at 0.7 MPa to eject metal blanks from warm stamping presses, utilizing the M20x1.5 rod thread for heavy tooling attachments.
Is the Airtac SE80 Standard Cylinder SE80X700SH the Right Cylinder?
Selecting this 80 mm bore makes sense when a 63 mm cylinder (1559 N push @0.5 MPa) is too weak, but a 100 mm bore (3927 N push @0.5 MPa) is physically oversized. The 700 mm stroke falls within the standard 1500 mm maximum for this bore, keeping it as a catalog item. Because the stroke is 700 mm, the unsupported piston rod is highly susceptible to bending under lateral loads; always pair this cylinder with an external linear guide to prevent rod-bearing damage.
As a true ISO 15552 profile cylinder, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing standard mounting accessories like FA front flanges or TC center trunnions. Remember that the adjustable air cushion only decelerates the piston near the stroke ends; it does not lock or hold a load. If your application must hold position without live air pressure, specify a BSE rod lock variant or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X700SH FAQ
The 80 mm bore generates 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum push of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X700SH is dimensionally interchangeable per ISO 15552, meaning it shares standard mounting footprints and port sizes (PT3/8) with other profile cylinders, though you must verify your existing rod thread and mounting accessory clearances.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X700SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.