Airtac SE80 Standard Cylinder SE80X750
The AirTAC Airtac SE80 Standard Cylinder SE80X750 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 750mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke750 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X750
The AirTAC SE80X750 is a double-acting single-rod profile cylinder built to ISO 15552 dimensions, delivering a robust 2513 N push force at 0.5 MPa. Its extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while maintaining standardized hole patterns for seamless retrofits.
This 80 mm bore unit manages a 750 mm stroke with a Ø25 mm piston rod and PT3/8 ports. Because this specific SKU lacks the -S magnet code, it is not equipped for CMSE or DMSE position sensing out of the box. Field-adjustable air cushions at both ends allow technicians to dial in end-of-stroke deceleration, protecting the mechanism from hard impacts during high-speed cycling.
Airtac SE80 Standard Cylinder SE80X750 Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X750 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X750
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X750 Is Used
Pallet Transfer Diverters
Provides the 2513 N push force needed to shove heavy timber pallets laterally across roller conveyors in distribution hubs over the full 750 mm stroke.
Corrugated Box Flappers
Drives the folding arms on high-speed corrugating machines, utilizing the adjustable end cushions to gently decelerate the 80 mm bore before it impacts the mechanical stops.
Injection Mold Ejection
Pushes large molded plastic bins out of the press cavity, where the 3518 N thrust at 0.7 MPa easily overcomes the part's static friction against the tooling.
Is the Airtac SE80 Standard Cylinder SE80X750 the Right Cylinder?
Stepping down to a 63 mm bore drops the 0.5 MPa push output to 1559 N, whereas moving up to a 100 mm bore increases it to 3927 N, letting you fine-tune the actuator to the exact load. At 750 mm of travel, the unsupported mass of the rod introduces significant bending moments on the front bearing cap; an external linear guide is strongly recommended to prevent premature seal wear and side-load damage.
As a true ISO 15552 profile cylinder, this model serves as a drop-in replacement for any standard 80 mm bore, 750 mm stroke unit with PT3/8 ports and matching mounting accessories. Remember that the integrated air cushion only decelerates the piston near stroke end and does not function as a brake; if your process must hold a vertical load without live air pressure, you must pair it with a BSE rod lock or an external pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X750 FAQ
At 0.5 MPa, the SE80X750 delivers 2513 N of push force and 2268 N of pull force. At 0.7 MPa, the push force increases to 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE80X750 is dimensionally interchangeable with any ISO 15552 profile cylinder sharing the same 80 mm bore, 750 mm stroke, PT3/8 ports, and standard mounting interface. Just ensure your existing hardware matches the ISO footprint before swapping.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X750
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.