Airtac SE80 Standard Cylinder SE80X760S
The AirTAC Airtac SE80 Standard Cylinder SE80X760S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 760mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke760 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X760S
The AirTAC SE80X760S is a double-acting, single-rod ISO 15552 profile cylinder engineered for heavy-duty linear motion. It delivers a robust 2513 N push force at 0.5 MPa (3518 N at 0.7 MPa), utilizing a 25 mm diameter piston rod and a PT3/8 port to efficiently move substantial loads over its 760 mm stroke. The square extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position sensors dropped into the standard grooves on three sides of the body. Field-adjustable pneumatic cushioning at both ends allows technicians to tune the end-of-stroke deceleration via a set screw, smoothly damping the high kinetic energy generated by the 80 mm bore without relying on fixed rubber bumpers.
Airtac SE80 Standard Cylinder SE80X760S Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X760S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 760 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X760S
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×760 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X760S Is Used
Pallet Transfer Diversion
Provides the 2513 N push force at 0.5 MPa needed to deflect heavy wooden pallets onto adjacent packaging lines, using the 760 mm stroke to clear the main conveyor path completely.
Injection Mold Ejection
Drives large plastic injection molding ejector plates, leveraging the 36 mm adjustable air cushion to softly decelerate the heavy mold assembly at the end of its 760 mm extraction cycle.
Automated Storage Retrieval
Actuates deep-reach extractor arms in automated storage systems, utilizing the integrated -S magnet with DMSE sensors to confirm precise tote positioning across the long 760 mm travel.
Is the Airtac SE80 Standard Cylinder SE80X760S the Right Cylinder?
Selecting the SE80X760S makes sense when your application requires pushing or lifting heavy assemblies over a long 760 mm travel. If you need to scale force down, the adjacent 63 mm bore provides 1559 N of push at 0.5 MPa; scaling up to the 100 mm bore yields 3927 N at 0.5 MPa. Because this cylinder features a 760 mm stroke, the extended 25 mm rod generates significant bending moments under side loads—an external guide rail is strongly recommended to prevent premature rod-bearing wear. As a standard ISO 15552 component, it serves as a drop-in dimensional replacement for other ISO 15552 cylinders, sharing identical mounting and PT3/8 port spacing. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load vertically if air pressure is lost, which requires a BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X760S FAQ
The SE80X760S generates 2513 N of push force and 2268 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 3518 N, with a maximum push capacity of 513 kgf at 1.0 MPa. It operates at a speed range of 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552, matching standard 80 mm mounting footprints and PT3/8 ports. However, the adjustable air cushion only decelerates the piston near stroke end; it does not function as a brake. If you need to hold a vertical load without live air pressure, you must use a BSE rod lock cylinder or an external pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X760S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.