Airtac SE80 Standard Cylinder SE80X900SH
The AirTAC Airtac SE80 Standard Cylinder SE80X900SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 900mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke900 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X900SH
The AirTAC SE80X900SH is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding, high-temperature automation. It generates 2513 N of push force at 0.5 MPa and 3518 N at 0.7 MPa, utilizing an 80 mm bore and a 900 mm stroke. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush into tight machinery frames.
This specific configuration includes a Viton (FKM) high-temperature seal rated for up to 150 C, and a built-in magnet for non-contact position sensing using CMSE reed or DMSE electronic switches. The field-adjustable pneumatic cushioning at both ends allows you to dial in end-of-stroke deceleration, protecting long-stroke loads from hard impacts.
Airtac SE80 Standard Cylinder SE80X900SH Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X900SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 900 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X900SH
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×900 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X900SH Is Used
Automotive Paint Curing Oven
With its 150 C FKM seal, this cylinder reliably actuates 900 mm stroke doors on high-temperature paint curing ovens where standard rubber seals would fail.
Pallet Strapping Machine
Provides 2513 N of push force at 0.5 MPa to extend and tension heavy-duty strapping heads across a wide 900 mm packaging bay.
Aluminum Extrusion Quench
Handles long-stroke 900 mm extraction of hot aluminum profiles from the press, utilizing the adjustable cushion to smoothly decelerate heavy moving masses.
Is the Airtac SE80 Standard Cylinder SE80X900SH the Right Cylinder?
At 0.5 MPa, this 80 mm bore provides 2513 N of push force. If your application requires less force, stepping down to the 63 mm bore yields 1559 N of push, while moving up to the 100 mm bore provides 3927 N. Because this is a 900 mm stroke, the unsupported rod length is substantial; you must use an external guide to prevent rod-bearing bending and premature seal wear under side loads. As a standard ISO 15552 cylinder, it serves as a drop-in replacement sharing the 80 mm PT3/8 port, M20x1.5 rod thread, and standardized mounting interface. Note that the air cushion only decelerates the piston near stroke end; it does not hold a load. If your process requires position holding without live air pressure, use a BSE rod lock variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X900SH FAQ
This 80 mm bore cylinder provides 2513 N of push force and 2268 N of pull force at 0.5 MPa. At 0.7 MPa, the push force is 3518 N, with a maximum push of 513 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, it is dimensionally interchangeable per ISO 15552 standards, allowing it to share mounting hardware with other profile cylinders. The built-in -S magnet is designed specifically for AirTAC CMSE reed switches and DMSE electronic sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X900SH
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.