Airtac SE80 Standard Cylinder SE80X920SCBCR
The AirTAC Airtac SE80 Standard Cylinder SE80X920SCBCR is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø80mm bore and 920mm stroke, PT3/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it a drop-in replacement for other ISO 15552 cylinders in automation lines.
- BoreØ80 mm
- Stroke920 mm
- Port sizePT3/8
- Acting typeDouble acting
- Rod threadM20×1.5
- CushionAdjustable, 36 mm
About the Airtac SE80 Standard Cylinder SE80X920SCBCR
The AirTAC SE80X920SCBCR is a double-acting single-rod ISO 15552 profile cylinder engineered for a 920 mm stroke. Delivering 2513 N of push force at 0.5 MPa and 2268 N of pull force, it operates at speeds from 30-800 mm/s. The square extruded aluminum barrel omits external tie rods, yielding a flush-mounting body that resists corrosion and simplifies bracket placement along its length.
This specific configuration includes a built-in magnet (-S) for CMSE reed or DMSE electronic position sensing, paired with a CB double clevis mount. Field-adjustable pneumatic cushioning at both ends allows mechanics to tune end-of-stroke deceleration, softening hard impacts during high-speed traverse. Because 920 mm exceeds the standard 1500 mm limit, this is a non-standard, made-to-order stroke.
Airtac SE80 Standard Cylinder SE80X920SCBCR Technical Specifications
| Model | Airtac SE80 Standard Cylinder SE80X920SCBCR |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø80 mm |
| Stroke | 920 mm |
| Acting type | Double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
| Max stroke | Up to 1500 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
Theoretical Output Force (Ø80mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2513 N | 2268 N |
| 0.7 MPa | 3519 N | — |
| Max (@1.0 MPa) | 513 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SE80 Standard Cylinder SE80X920SCBCR
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 80 | Bore size in mm. |
| ×920 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Where the Airtac SE80 Standard Cylinder SE80X920SCBCR Is Used
Pallet Transfer Line Diverter
Ideal for shunting heavy pallets across a 900 mm gap, using its 2513 N push force to overcome cart inertia and the CB clevis to pivot smoothly.
Corrugated Box Flap Folder
Drives a mechanical arm to fold large corrugated flaps on case erectors, relying on the 920 mm stroke and DMSE sensors for timing precision.
Press Feed Unloader
Extracts stamped metal parts from a press bed, utilizing the full 920 mm extension and the adjustable cushion to prevent end-cap slamming.
Is the Airtac SE80 Standard Cylinder SE80X920SCBCR the Right Cylinder?
If your load requires less thrust, the adjacent SE63X200 delivers 1559 N push at 0.5 MPa, whereas stepping up to the SE100X920 provides 3927 N push. This 80 mm bore yields 2513 N push and 2268 N pull at 0.5 MPa, peaking at 513 kgf under 1.0 MPa. The PT3/8 port and M20x1.5 rod thread handle substantial flow rates, but a 920 mm unsupported stroke invites rod-bearing bending. An external guide is strongly recommended to prevent premature seal wear from side loads.
The CB clevis mount accommodates pivoting articulation, while the -S magnet enables CMSE or DMSE sensor tracking. Note that the adjustable air cushion only decelerates the piston near stroke end; it does not hold loads. If your application loses air pressure or centers the valve, the cylinder will drift, requiring a BSE rod lock for true position holding.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT/G)
- ✓ Magnet (-S) for CMSE/DMSE sensors?
- ✓ Side load — consider a guided cylinder
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Adjust end cushion screws for smooth stops.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC/FTC/TCM1/TCM2).
- check Installation by qualified personnel per AirTAC docs.
Airtac SE80 Standard Cylinder SE80X920SCBCR FAQ
This 80 mm bore cylinder provides 2513 N push and 2268 N pull at 0.5 MPa, 3518 N push at 0.7 MPa, and a maximum of 513 kgf at 1.0 MPa. It uses a PT3/8 port and a 25 mm rod with an M20x1.5 thread.
Yes, the SE80X920SCBCR is dimensionally interchangeable per ISO 15552 standards. You can swap it directly with other ISO 15552 profile cylinders using the same CB mounting hardware and PT3/8 port spacing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models usually ship in 3-4 days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac SE80 Standard Cylinder SE80X920SCBCR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.