verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC SEJ Series · ISO 15552 Adjustable-Stroke Cylinder

Airtac SEJ Adjustable Cylinder SEJ32X240-100S

The AirTAC SEJ Adjustable Cylinder SEJ32X240-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø32mm unit covers an effective stroke of 140–240mm without changing cylinders. Force is equal in both directions.

  • BoreØ32 mm
  • Nominal stroke240 mm
  • Adjust window100 mm
  • Effective stroke140–240 mm
  • Port sizePT1/8
  • CushionAdjustable, 27 mm
$86.76 $94.26Save 7% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every SEJ32 stroke, mounting and version on one page All SEJ32 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac SEJ Adjustable Cylinder SEJ32X240-100S

The AirTAC SEJ32X240-100S is a double-acting, double-rod ISO 15552 profile cylinder with a 100 mm adjustable stroke window, letting you dial the retract end from 140 mm up to 240 mm. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 345 N each way at 0.5 MPa. The included -S magnet enables position detection with CMSE reed or DMSE electronic sensors.

You set the exact end-position mechanically via a stop screw on the back rod, then lock it in place for repeatable cycles. Built to ISO 15552 and VDMA 24562 dimensional standards, this extruded aluminum profile cylinder omits external tie rods. It features field-adjustable air cushions at both ends to decelerate the 12 mm rod near stroke extremes, operating at speeds of 30-800 mm/s via PT1/8 ports.

Airtac SEJ Adjustable Cylinder SEJ32X240-100S Technical Specifications

ModelAirtac SEJ Adjustable Cylinder SEJ32X240-100S
SeriesSEJ ISO 15552 adjustable-stroke cylinder
Bore sizeØ32 mm
Nominal stroke240 mm
Adjustment window100 mm (140–240 mm)
ConfigurationDouble rod, double acting
Port sizePT1/8
Rod threadM10×1.25
Operating pressure0.15 – 1.0 MPa
Proof pressure1.5 MPa
Temperature-20 to +70 °C (0–150 °C with FKM seals)
Speed range30 – 800 mm/s
CushionAdjustable, 27 mm

Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).

Theoretical Output Force (Ø32mm)

PressureForce (both directions)
0.5 MPa346 N
0.7 MPa484 N
Max (@1.0 MPa)70 kgf

A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.

Model Code: Airtac SEJ Adjustable Cylinder SEJ32X240-100S

SEJISO 15552 double-rod double-acting cylinder with adjustable stroke.
32Bore size in mm.
×240Nominal stroke length in mm.
-100Adjustment stroke window in mm (options: 10/20/30/40/50/75/100).
-SOptional built-in magnet for CMSE / DMSE sensor sensing.

Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).

Where the Airtac SEJ Adjustable Cylinder SEJ32X240-100S Is Used

swap_horiz

Multi-Part Changeover

Dial the retract stroke from 140 to 240 mm to switch a packaging line between varying carton depths without swapping hardware, using the 345 N both-way force to push and pull reliably.

tune

Dispenser Calibration

Fine-tune the exact end-stop on an adhesive dispensing head during commissioning, locking the back-rod screw once the bead placement is perfect to ensure repeatable 0.5 MPa actuation.

precision_manufacturing

Trial Positioning Jig

Use the 100 mm window to test multiple pick-and-place end points for a lightweight electronic component handler, relying on the magnet and DMSE sensors to verify the adjusted position.

Is the Airtac SEJ Adjustable Cylinder SEJ32X240-100S the Right Cylinder?

Confirm this 100 mm adjustment window covers your machine's required positioning range. If you need less fine-tuning, a fixed-stroke SED saves complexity, or you could step down to a 25 mm bore (though standard SEJ sizes start at 32). Stepping up to a 40 mm bore increases your both-way force to 528 N at 0.5 MPa. For any fixed-position fail-safe holding during air loss, note this cylinder does not lock; add an external rod lock or BSED.

Because the 240 mm stroke exceeds 300 mm is not met here, but at 240 mm you must still manage side loads with external guides to protect the M10x1.25 rod thread. Mounting options include Basic, FA, LB, TC, FTC, TCM1, and TCM2 (omitting FB/CA/CB/CR). To match an ISO 15552 replacement, verify the 32 mm bore, 240 mm nominal stroke, PT1/8 port, and magnet option.

AirtacDistr lists every SEJ32 order code with its price on one page at https://airtacdistr.com/products/airtac-sej32-adjustable-cylinder

Quick checklist

  • ✓ Need on-machine stroke fine-tuning?
  • ✓ Adjustment window (100mm) covers your range
  • ✓ Equal force both directions OK
  • ✓ Port/thread type (PT/G)
  • ✓ Magnet (-S) for CMSE/DMSE sensors?
Ask an Engineer

Installation & Maintenance Notes

  • check Use clean air filtered to 40µm or finer.
  • check Keep within 0.15 – 1.0 MPa operating pressure.
  • check Set the stop screw within the 100mm window; lock it after adjusting.
  • check Adjust end cushion screws for smooth stops.
  • check Use correct mounting accessory (LB/FA/TC/FTC/TCM1/TCM2).
  • check Installation by qualified personnel per AirTAC docs.

Airtac SEJ Adjustable Cylinder SEJ32X240-100S FAQ

A stop screw on the rear rod mechanically shortens the retract stroke over a 100 mm window. You can set the effective stroke anywhere from 140 mm up to the full 240 mm, then lock the screw for precise end-position tuning on the machine.

Because it is a double-rod cylinder, force is equal both ways: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.

verified

Authorized Export Seller

Genuine AirTAC parts produced by AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Related AirTAC SEJ Cylinders

Request a Quote for Airtac SEJ Adjustable Cylinder SEJ32X240-100S

Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for SEJ32X240-100S and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.