
The AirTAC SEJ Adjustable Cylinder SEJ32X350-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø32mm unit covers an effective stroke of 300–350mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X350-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window, allowing the retract end to be dialed in for an effective stroke range of 300 to 350 mm. A rod exits both ends, meaning the annulus area is identical in both directions, yielding an equal force of 345 N each way at 0.5 MPa. This symmetry is critical when drive force must remain constant regardless of travel direction.
Because the stroke extends to 350 mm, the M10x1.25 rod ends should be paired with external guides to prevent side loading on the 12 mm rod. The rear rod uses a mechanical stop screw to set the precise end position, which must be locked after commissioning. The included magnet (-S) supports CMSE reed and DMSE electronic sensors for position feedback.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X350-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 350 mm |
| Adjustment window | 50 mm (300–350 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×350 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 300-350 mm retract stroke to match varying board widths on an assembly line pusher, using the 345 N both-way force to shuttle panels without direction-based speed drops.
Quickly reconfigure a carton folding stop by adjusting the 50 mm window during product changeover, relying on the equal 483 N @0.7 MPa force to consistently fold heavy cardstock.
Fine-tune the exact retract distance of a glue dispensing nozzle against a mechanical stop screw, locking the 12 mm rod in place for repeatable adhesive bead placement.
Verify the 50 mm adjustment window covers your machine's fine-tuning range, letting you dial the retract stroke exactly between 300 and 350 mm without swapping hardware. If you need less force, the adjacent bore down is 32 mm (this model, providing 345 N at 0.5 MPa); stepping up to the 40 mm bore increases both-way output to 528 N at 0.5 MPa. If the end position never varies after commissioning, a fixed-stroke SED cylinder is sufficient.
For any 350 mm stroke, external guides are recommended to manage side loads on the extended rod. Note that a plain SEJ does not hold position on air loss; the adjustable air cushion and stop screw only decelerate the piston and set the mechanical end, so add an external rod lock for fail-safe holding. This ISO 15552 dimensionally interchangeable cylinder uses a PT1/8 port and supports Basic, FA, LB, TC, FTC, TCM1, and TCM2 mounts.
AirtacDistr lists every SEJ32 order code with its price on one page at https://airtacdistr.com/products/airtac-sej32-adjustable-cylinder
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke by up to 50 mm. For this SEJ32X350-50S model, the effective stroke range is 300 to 350 mm. You set the exact end position during commissioning and lock the screw in place.
Because it is a double-rod cylinder, the force is identical in both directions. It generates 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.