
The AirTAC SEJ Adjustable Cylinder SEJ32X50-50SH is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø32mm unit covers an effective stroke of 0–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ32X50-50SH is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical extend and retract annulus areas. You get an equal force of 345 N each way at 0.5 MPa. The Viton (FKM) seal extends the operating temperature range up to 150 C.
This unit features a 50 mm adjustable stroke window. A stop screw on the back rod lets you dial the retract end down, giving an effective stroke range of 0-50 mm. You lock the screw after setting the exact end position. The extruded aluminum barrel has no external tie rods, and field-adjustable air cushions at both ends decelerate the load near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ32X50-50SH |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø32 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 50 mm (0–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/8 |
| Rod thread | M10×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 32 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 0-50 mm retract position on a fluid dispenser head. The equal 345 N both-way force ensures consistent valve pressure during precise fill cycles.
Adjust the mechanical stop to match varying part heights on a small conveyor line. The 50 mm window allows rapid changeover without swapping cylinder hardware.
Find the optimal engagement distance on a lab test rig. The FKM seals handle 150 C thermal cycling, while the back-rod stop screw locks the trial position in place.
The 50 mm adjustment window fully covers the 0-50 mm effective stroke range, making this cylinder ideal for prototyping and dialing in precise end stops. If you need less force, stepping down is not possible as 32 mm is the smallest bore. Stepping up to a 40 mm bore yields 528 N each way at 0.5 MPa. If your stroke is fixed and never changes, a standard SED double-rod cylinder is sufficient.
The adjustable air cushion and mechanical stop screw decelerate the load and set the end position, but a plain SEJ does not hold position on air loss. For fail-safe holding, use an external rod lock. This PT1/8 ported, magnet-equipped (CMSE/DMSE compatible) cylinder is dimensionally interchangeable per ISO 15552. With a 50 mm stroke, side loads are minimal, but always guide external loads to prevent rod binding.
AirtacDistr lists every SEJ32 order code with its price on one page at https://airtacdistr.com/products/airtac-sej32-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 50 mm window. You can dial the effective stroke anywhere from 0 to 50 mm, then lock the screw to set the exact end position.
The double-rod design provides equal force in both directions: 345 N at 0.5 MPa, 483 N at 0.7 MPa, and a maximum of 70 kgf at 1.0 MPa. The stop screw and air cushions decelerate the load but do not hold position on air loss; use an external rod lock for fail-safe holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.