
The AirTAC SEJ Adjustable Cylinder SEJ40X100-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø40mm unit covers an effective stroke of 25–100mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ40X100-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75mm adjustable stroke window, letting you dial the retract end from 25mm up to 100mm. A rod exits both ends, yielding identical annulus areas for equal force and speed in both directions. It delivers 528 N each way at 0.5 MPa.
This bore 40 unit uses a PT1/4 port and a Ø16mm rod with an M12x1.25 thread. The rear stop screw sets the precise mechanical end position, which you lock down after fine-tuning. The integrated -S magnet enables position detection with CMSE reed or DMSE electronic sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ40X100-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø40 mm |
| Nominal stroke | 100 mm |
| Adjustment window | 75 mm (25–100 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M12×1.25 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 528 N |
| 0.7 MPa | 739 N |
| Max (@1.0 MPa) | 108 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 40 | Bore size in mm. |
| ×100 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 25-100mm retract stroke to perfectly seat electronic connectors without crushing housings, leveraging the equal 528 N both-way force for stable push and pull.
Quickly adjust the mechanical end stop to accommodate different pallet heights on a packaging line, locking the back-rod screw for repeatable 0.5 MPa actuation.
Fine-tune the clamping reach during machine commissioning to avoid deflecting delicate castings, relying on the 30mm adjustable air cushion to decelerate the load.
Verify the 75mm adjustment window covers your required positioning range. If you need less force, the adjacent bore 32 provides 345 N at 0.5 MPa; if you need more, stepping up to bore 50 yields 825 N both ways. If your machine never requires stroke changes, a fixed-stroke SED cylinder is sufficient.
For direct ISO 15552 replacement, match the 100mm nominal stroke, 75mm window, PT1/4 port, and your mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Note that the air cushion decelerates the load near stroke end but does not hold position on air loss; use an external rod lock for fail-safe holding.
AirtacDistr lists every SEJ40 order code with its price on one page at https://airtacdistr.com/products/airtac-sej40-adjustable-cylinder
Quick checklist
The cylinder has a 75mm adjustment window on the retract end. You can mechanically dial the effective stroke anywhere from 25mm up to the full 100mm nominal stroke using the back-rod stop screw, then lock it in place.
Because the rod exits both ends, force is identical in both directions. It provides 528 N at 0.5 MPa, 739 N at 0.7 MPa, and a maximum of 108 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.