
The AirTAC SEJ Adjustable Cylinder SEJ50X150-20S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø50mm unit covers an effective stroke of 130–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X150-20S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 20mm adjustable stroke window. By turning the mechanical stop screw on the back rod, you dial the retract stroke from 130 mm up to 150 mm to perfectly match a stop or sensor target.
This design eliminates the need to swap hardware when commissioning a new part height. The extruded aluminum barrel has no external tie rods, and the included -S magnet allows mounting CMSE reed or DMSE electronic sensors along the body. Adjustable air cushions at both ends decelerate the 20 mm rod near stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X150-20S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 20 mm (130–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 130-150 mm retract position during a stamping press changeover to hit exact material stops, leveraging the equal 825 N both-way force to pull the feed arm back reliably.
Adjust the retract stroke on the fly to accommodate different pallet heights on a conveyor line without disassembling the cylinder hardware.
Fine-tune the downward clamping end position during assembly commissioning, using the mechanical stop screw to set a precise 130-150 mm travel for delicate parts.
Verify the 20 mm adjustment window covers your target end-position range. If you need less force, the 40 mm bore provides 528 N both ways at 0.5 MPa; if your load is heavier, step up to the 63 mm bore for 1402 N. If your end position never changes after commissioning, a fixed-stroke SED cylinder is sufficient. Remember that the air cushion and stop screw only set the mechanical end and decelerate near stroke end; a plain SEJ does not hold position on air loss. For fail-safe holding, use an external rod lock or BSED series.
When replacing an ISO 15552 cylinder, match the 50 mm bore, 150 mm nominal stroke, PT1/4 port, and mounting choice from the available Basic, FA, LB, TC, FTC, TCM1, or TCM2 set. This configuration omits FB, CA, CB, and CR mounts. Because the overall length is longer than a double-rod cylinder to house the back rod, ensure your machine envelope has clearance.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
The retract end has a mechanical stop screw on the back rod that allows you to dial the effective stroke down from the 150 mm nominal maximum to 130 mm. You set the exact end position during commissioning and lock it in place.
Because a rod exits both ends, the force is identical in both extend and retract directions. It provides 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.