
The AirTAC SEJ Adjustable Cylinder SEJ50X150-40S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 40mm window, so this Ø50mm unit covers an effective stroke of 110–150mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X150-40S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 40 mm adjustable retract window, yielding an effective stroke range of 110-150 mm. A rod exits both ends, creating identical annulus areas. This guarantees equal force and speed in both directions, delivering 825 N each way at 0.5 MPa.
Because it is an extruded aluminum ISO 15552 cylinder, it omits external tie rods for a clean exterior. The back-rod stop screw lets you dial in the exact end-position on the machine during commissioning, which you then lock in place. The included -S magnet supports CMSE reed and DMSE electronic sensors for position confirmation.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X150-40S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 150 mm |
| Adjustment window | 40 mm (110–150 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 40mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×150 | Nominal stroke length in mm. |
| -40 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the 110-150 mm retract stop to match varying back-gauge finger depths during sheet metal forming, utilizing the 825 N both-way force for consistent part indexing.
Quickly reposition the mechanical stop screw to accommodate different carton heights on a packaging line, ensuring precise 110-150 mm end-positioning without swapping hardware.
Fine-tune the clamping end-point during machine commissioning to avoid crushing delicate housings, locking the back-rod screw once the exact 110-150 mm position is achieved.
Verify the 40 mm adjustment window covers your required end-position variance. If 825 N at 0.5 MPa is excessive, step down to the 40 mm bore (528 N both ways); if undersized, step up to the 63 mm bore (1402 N). If your stop point never changes, a fixed-stroke SED cylinder is sufficient. For replacing an ISO 15552 unit, match the 50 mm bore, 150 mm nominal stroke, PT1/4 port, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2). The adjustable air cushion at both ends decelerates the load near stroke end but does not hold position on air loss; for fail-safe holding, use an external rod lock or BSED.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
The 40 mm adjustment window allows you to mechanically shorten the retract stroke from the nominal 150 mm down to 110 mm. You set the exact end-position using the stop screw on the back rod and lock it in place.
Because the rod exits both ends, force is identical in both directions: 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.