
The AirTAC SEJ Adjustable Cylinder SEJ50X80-75S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 75mm window, so this Ø50mm unit covers an effective stroke of 5–80mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ50X80-75S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 75 mm adjustable stroke window. A rod exits both ends, yielding equal annulus areas and a balanced drive force of 825 N each way at 0.5 MPa. By turning the stop screw on the back rod, you mechanically shorten the retract stroke anywhere from 5 mm up to the full 80 mm nominal length.
This extruded aluminum barrel omits external tie rods for a clean ISO 15552 dimensional interchange. The -S magnet option enables direct mounting of CMSE reed or DMSE electronic sensors. Adjustable air cushions at both ends provide smooth deceleration near the stroke limits, while the PT1/4 port and M16x1.5 rod thread ensure standard pneumatic integration.
| Model | Airtac SEJ Adjustable Cylinder SEJ50X80-75S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø50 mm |
| Nominal stroke | 80 mm |
| Adjustment window | 75 mm (5–80 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 75mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 825 N |
| 0.7 MPa | 1155 N |
| Max (@1.0 MPa) | 168 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 50 | Bore size in mm. |
| ×80 | Nominal stroke length in mm. |
| -75 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial in the exact 5-80 mm clamping reach on a stamping press during setup, leveraging the 825 N both-way force to seat dies accurately.
Quickly adjust the retract stop to accommodate varying product heights on a packaging conveyor without swapping out cylinder hardware.
Mechanically fine-tune the end-of-stroke stop on an R&D test rig to find the optimal engagement distance before locking the screw.
Confirm the 75 mm adjustment window covers your required end-position range. If you need less fine-tuning, a fixed-stroke SED50X80 is sufficient. For sizing both ways: stepping down to a 40 mm bore yields 528 N both-way force at 0.5 MPa, while stepping up to a 63 mm bore provides 1402 N. The plain SEJ does not hold position on air loss; for fail-safe holding, specify a BSED or an external rod lock. Ensure your ISO 15552 replacement matches the 50 mm bore, 5-80 mm window, PT1/4 port, and magnet option.
AirtacDistr lists every SEJ50 order code with its price on one page at https://airtacdistr.com/products/airtac-sej50-adjustable-cylinder
Quick checklist
A stop screw on the rear protruding rod lets you mechanically dial the retract stroke within a 75 mm window. The effective stroke range is 5 mm to 80 mm, which you set and lock during commissioning without changing hardware.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 825 N at 0.5 MPa, 1154 N at 0.7 MPa, and a maximum of 168 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.