
The AirTAC SEJ Adjustable Cylinder SEJ63X300-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø63mm unit covers an effective stroke of 250–300mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ63X300-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable retract window, allowing the effective stroke to be fine-tuned from 250 mm up to the full 300 mm. A rod exits both ends, ensuring the annular area remains identical in both directions.
Equipped with a -S magnet, the cylinder supports CMSE reed and DMSE electronic sensors for position detection. The retract position is set via a mechanical stop screw on the back rod, which must be locked after dialing in the target end position. The extruded aluminum barrel conforms to ISO 15552 dimensions with no external tie rods, and adjustable air cushions at both ends decelerate the load near stroke extremes.
| Model | Airtac SEJ Adjustable Cylinder SEJ63X300-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Nominal stroke | 300 mm |
| Adjustment window | 50 mm (250–300 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M16×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 1402 N |
| 0.7 MPa | 1962 N |
| Max (@1.0 MPa) | 286 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×300 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Delivers 1962 N both ways at 0.7 MPa to position a press sub-assembly. The 50 mm window lets operators dial the exact 250-300 mm closing height for different material thicknesses during commissioning.
Provides 1402 N at 0.5 MPa to halt pallets on a conveyor. The adjustable back-rod stop screw allows quick changeover between 250 mm and 300 mm stop distances without swapping hardware.
Applies equal push and pull forces for component fatigue testing. The 50 mm retract window allows researchers to tune the exact deformation endpoint precisely on the machine.
Verify the 50 mm adjustment window covers your required end-position range. If your application needs less force, the adjacent bore down is 50 mm, delivering 825 N both ways at 0.5 MPa; if you need more power, the next bore up is 80 mm, providing 2268 N at 0.5 MPa. If the exact stroke never varies during operation, a fixed-stroke SED cylinder is sufficient. For position holding on air loss, note that this plain SEJ cylinder does not lock; you will need a BSED or an external rod lock for fail-safe holding.
When replacing an ISO 15552 cylinder, match the 63 mm bore, 300 mm stroke, 50 mm adjustment window, PT3/8 port, and mounting style (Basic, FA, LB, TC, FTC, TCM1, or TCM2). Because the stroke is 300 mm, external guide rails are recommended to prevent rod side-loading and binding over the extended travel.
AirtacDistr lists every SEJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sej63-adjustable-cylinder
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke over a 50 mm window. You can dial the effective stroke anywhere from 250 mm up to 300 mm, then lock the screw in place. It is a mechanical end-position setting, not a pneumatic mid-stroke lock.
Because the rod exits both ends, the force is identical in both directions: 1402 N at 0.5 MPa, 1962 N at 0.7 MPa, and a maximum of 286 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.