
The AirTAC SEJ Adjustable Cylinder SEJ80X180-50S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø80mm unit covers an effective stroke of 130–180mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X180-50S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. A stop screw on the rear rod lets you dial the retract end position, yielding an effective stroke range of 130 to 180 mm.
This extruded aluminum barrel omits external tie rods for a clean profile and includes field-adjustable air cushions at both ends to decelerate the 25 mm rod near stroke limits. The factory-installed magnet (-S) directly supports CMSE reed and DMSE electronic sensors for position feedback. You must lock the stop screw mechanically after setting your end position to prevent drift during machine commissioning.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X180-50S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 180 mm |
| Adjustment window | 50 mm (130–180 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×180 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 50 mm retract window to match varying die heights on a stamping press. The equal 3175 N both-way force securely retracts and holds the heavy tooling without sagging.
Adjust the stroke from 130 to 180 mm on a packaging line to deflect different carton sizes. The double-rod design maintains identical push and pull speeds for consistent timing.
Fine-tune the exact end-of-stroke position during equipment setup. The rear stop screw lets you hit a precise mechanical stop, while the -S magnet works with DMSE sensors to verify position.
Verify the 50 mm adjustment window covers your positioning range; if you need less fine-tuning, a fixed-stroke SED80 saves complexity. For sizing both ways, stepping down to a 63 mm bore yields 1402 N both ways at 0.5 MPa, while stepping up to a 100 mm bore provides 3681 N. This 80 mm bore generates 3175 N at 0.7 MPa, serving as the middle ground for medium-high load drives.
The adjustable air cushion and rear stop screw decelerate the load and set the mechanical end, but a plain SEJ does not hold position on air loss. For fail-safe holding, specify a BSED or an external rod lock. When replacing an ISO 15552 cylinder, match the 180 mm stroke, 50 mm window, PT3/8 port, and your mounting choice from Basic, FA, LB, TC, FTC, TCM1, or TCM2.
AirtacDistr lists every SEJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-sej80-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 50 mm window. For the 180 mm nominal stroke, you can adjust the effective stroke anywhere from 130 mm up to 180 mm. You must lock the screw after setting your desired end position.
Because it is a double-rod cylinder, the force is identical in both directions. It provides 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, and a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.