Airtac TACE Guided Compact Cylinder TACE25X10
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X10 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 10mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke10 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X10
Built as a double acting, non-rotating ISO 21287 compact cylinder, the TACE25X10 drives a 25 mm bore over a 10 mm stroke, with twin guide rods on a yoke that stop the tooling turning and carry side load. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N, rising to 343.6 N push and 288.6 N pull at 0.7 MPa, with a theoretical peak of 50.1 kgf at 1.0 MPa. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight jigs, guards and gantries.
Plan on roughly 147 N of usable force at 0.5 MPa, about 60% of the rated push, and expect the full 245.4 N to lift about 25 kg vertically - halve that to 12 kg for a 2:1 margin. The hard-anodized aluminium body carries an S45C hard-chrome rod, with a fixed TPU bumper at each end absorbing end-of-stroke energy. Sensing needs the optional -S magnet code; without it no CMSE or DMSE switch can be mounted. Speed runs 30-500 mm/s on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi).
Airtac TACE Guided Compact Cylinder TACE25X10 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X10 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 10 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X10
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X10 Is Used
Bearing press on an assembly bench
Pressing small bearings into pump housings on an electronics assembly line: 245.4 N push at 0.5 MPa suits light press-fit work, and the twin-guide yoke keeps the arbor square over the short 10 mm stroke.
Drill jig clamp for aluminium brackets
Clamping aluminium brackets in a CNC drill fixture: the 10 mm stroke closes fast, the guide rods take the side thrust of the clamp pad, and the compact body tucks under the jig plate where a full-length cylinder will not.
Tray-to-tray lift with end check
Lifting small aluminium housings between trays on a packaging cell - about 12 kg vertical lift with a 2:1 margin at 0.5 MPa - and the optional -S magnet lets a DMSE switch confirm each end position.
Is the Airtac TACE Guided Compact Cylinder TACE25X10 the Right Cylinder?
For light press and clamp work near 245 N at 0.5 MPa, the 25 mm bore is the right pick; drop to a 20 mm bore (157.1 N push) for gentler loads or step up to 32 mm (402.1 N) when the job needs more muscle. The piston drifts if air is lost, so add a rod lock or pilot check valve wherever a load must stay held. The rod ends in a female M6x1.0 thread, with no male-thread option on the yoke. Mount via FB flange, CA/CB clevis, CR or FTC, and order the -S code if CMSE or DMSE switches are planned.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X10 FAQ
At 0.5 MPa the 25 mm bore pushes 245.4 N and pulls 206.2 N; at 0.7 MPa that rises to 343.6 N push and 288.6 N pull. Theoretical maximum force is 50.1 kgf at 1.0 MPa. The rod drifts when air is removed, so fit a rod lock or pilot check valve if the load must stay in place.
The ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Mounting choices are FB, CA, CB, CR and FTC, with M5x0.8 PT ports on this bore. Feedback requires the optional -S magnet; only with that code can CMSE or DMSE switches be mounted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X10
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.