Airtac TACE Guided Compact Cylinder TACE25X25S
The AirTAC Airtac TACE Guided Compact Cylinder TACE25X25S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 25mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke25 mm
- Port sizeM5×0.8
- Acting typeDouble acting, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE25X25S
Built to the ISO 21287 short-body format, the TACE25X25S is a double acting, non-rotating compact cylinder: a 25 mm bore with a 25 mm stroke, twin guide rods on a yoke that stop the tooling rotating and carry side load, and a hard-anodized aluminium body with an S45C hard-chrome plated 10 mm rod. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N, and the short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding where a full-length body will not fit.
A fixed TPU bumper at each end absorbs end-of-stroke energy, speed runs 30-500 mm/s, and the air supply is 0.15-1.0 MPa (22-145 psi) filtered to 40 um. Because this model carries the optional -S magnet, CMSE or DMSE reed and solid-state switches can be mounted anywhere along the body slots. For sizing, treat roughly 147 N of the 0.5 MPa push as usable work; that is enough to lift about 25 kg on paper, or about 12 kg with a 2:1 margin.
Airtac TACE Guided Compact Cylinder TACE25X25S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE25X25S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 25 mm |
| Acting type | Double acting, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE25X25S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE25X25S Is Used
Fixture eject in a 25 mm pocket
Ejects a machined aluminium boss from its nest on a rotary indexing table, where the 25 mm stroke clears the part and the twin-guide yoke keeps the pusher square to the nest.
Carton flap tuck on a sealer
Tucks the leading flap on a small carton sealing head; 245.4 N at 0.5 MPa is ample for light folding work and the short body fits inside the sealer frame.
PCB tray push-off
Pushes populated PCB trays between test stations on an electronics line; the non-rotating twin guides keep the pusher plate aligned with the tray edge without an external guide.
Is the Airtac TACE Guided Compact Cylinder TACE25X25S the Right Cylinder?
Step down to the 20 mm bore (157.1 N push at 0.5 MPa) when the load is lighter and the pocket is tighter, or step up to the 32 mm bore (402.1 N push) when the fixture needs more clamping force. Remember the piston drifts when air is lost, so a load that must stay put calls for a rod lock or a pilot check valve in the circuit. Mounting choices are FB flange, CA/CB clevis, CR and FTC, and since the -S magnet is fitted on this model, CMSE / DMSE switches can be added without reordering the cylinder.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE25X25S FAQ
At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa push rises to 343.6 N and pull to 288.6 N. The theoretical maximum at 1.0 MPa is 50.1 kgf. Air supply is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed runs 30-500 mm/s.
The ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end to absorb end-of-stroke shock. Mounting options are FB flange, CA/CB clevis, CR and FTC. Because this model carries the optional -S magnet, CMSE or DMSE switches can be clipped into the body slots for end-of-stroke signalling; without the -S code there is no magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE25X25S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.