Airtac TACE Guided Compact Cylinder TACE63X15S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X15S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 15mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke15 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X15S
The TACE63X15S is a double acting, non-rotating compact cylinder built to ISO 21287 with a 63 mm bore and a short 15 mm stroke. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square with no external guide. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa those figures rise to 2182.1 N and 2041.3 N, with a theoretical peak of 317.9 kgf at 1.0 MPa.
The hard-anodized aluminium body with an S45C hard-chrome rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs and gantries. Plan on roughly 935 N of real work at 0.5 MPa, about 60% of rated push, enough to lift about 79 kg vertically with a 2:1 margin. The -S magnet this model carries lets CMSE or DMSE switches report rod position, and fixed TPU bumpers absorb end-of-stroke energy at both ends.
Airtac TACE Guided Compact Cylinder TACE63X15S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X15S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 15 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X15S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X15S Is Used
Gearbox housing clamping
A 15 mm clamp stroke with 1558.6 N of push at 0.5 MPa seats a locating clamp on an aluminium gearbox housing, while the twin-guide yoke keeps the clamp shoe square to the fixture.
Bearing press fitting
Short-stroke pressing of small bearings into pump end covers, where the twin guide rods hold the press shoe parallel and the 2182.1 N push available at 0.7 MPa completes the seat.
Die segment lift and locate
Raising a 79 kg locating block in a stamping die: this bore lifts about 79 kg vertically with a 2:1 margin, and the 15 mm stroke suits a short lift-and-locate move.
Is the Airtac TACE Guided Compact Cylinder TACE63X15S the Right Cylinder?
For this 15 mm stroke, bore 50 gives 981.7 N push at 0.5 MPa and bore 80 gives 2513.3 N, so the 63 mm sits squarely between them for medium clamping and pressing work. Air drives the rod in both directions, so it drifts if pressure is lost - add a rod lock or pilot check valve where a load must stay put. Mounting choices are FB flange, CA/CB clevis, CR and FTC; the 1/8" port serves this bore, and the female M10x1.5 rod thread takes standard tooling.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X15S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N. At 0.7 MPa the push is 2182.1 N and the pull 2041.3 N. The theoretical maximum is 317.9 kgf at 1.0 MPa. Operating pressure spans 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating, and rod speed runs 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Mountings include FB flange, CA/CB clevis, CR and FTC. Because this model carries the optional -S magnet, CMSE or DMSE reed and solid-state switches can be fitted to the body slots; the rod ends in a female M10x1.5 thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X15S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.